Subversion Repositories Code-Repo

Rev

Blame | Last modification | View Log | RSS feed

// <editor-fold defaultstate="collapsed" desc="Configuration Bits">
// PIC16F1825 Configuration Bit Settings

// CONFIG1
#pragma config FOSC = INTOSC    // Oscillator Selection (INTOSC oscillator: I/O function on CLKIN pin)
#pragma config WDTE = OFF       // Watchdog Timer Enable (WDT disabled)
#pragma config PWRTE = OFF      // Power-up Timer Enable (PWRT disabled)
#pragma config MCLRE = ON       // MCLR Pin Function Select (MCLR/VPP pin function is digital input)
#pragma config CP = OFF         // Flash Program Memory Code Protection (Program memory code protection is disabled)
#pragma config CPD = OFF        // Data Memory Code Protection (Data memory code protection is disabled)
#pragma config BOREN = ON       // Brown-out Reset Enable (Brown-out Reset enabled)
#pragma config CLKOUTEN = OFF   // Clock Out Enable (CLKOUT function is disabled. I/O or oscillator function on the CLKOUT pin)
#pragma config IESO = ON        // Internal/External Switchover (Internal/External Switchover mode is enabled)
#pragma config FCMEN = ON       // Fail-Safe Clock Monitor Enable (Fail-Safe Clock Monitor is enabled)

// CONFIG2
#pragma config WRT = OFF        // Flash Memory Self-Write Protection (Write protection off)
#pragma config PLLEN = ON       // PLL Enable (4x PLL enabled)
#pragma config STVREN = ON      // Stack Overflow/Underflow Reset Enable (Stack Overflow or Underflow will cause a Reset)
#pragma config BORV = LO        // Brown-out Reset Voltage Selection (Brown-out Reset Voltage (Vbor), low trip point selected.)
#pragma config LVP = OFF        // Low-Voltage Programming Enable (High-voltage on MCLR/VPP must be used for programming)
// </editor-fold>

#include "defines.h"
#include "INTERRUPTS.h"
#include "I2C1.h"
#include "I2C2.h"
#include "TLC59116.h"
#include "MCP23009.h"

void Pins_Init(void) {
    // Set all pins to digital I/O
    ANSELA = 0x0;
    ANSELB = 0x0;
    ANSELC = 0x0;

    // Enable weak pull-up if WPU bit is set
    OPTION_REGbits.nWPUEN = 0;

    // Initialize interrupt inputs
    LSM303_INT_TRIS = 1;
    L3GD20_INT_TRIS = 1;
    BTN_INT_TRIS = 1;

    // Initialize UART pins
    UART_RX_TRIS = 1;
    UART_TX_TRIS = 0;

    // Initialize I2C address pins
    I2C_ADDR_0_TRIS = 1;
    I2C_ADDR_1_TRIS = 1;
    I2C_ADDR_2_TRIS = 1;
    I2C_ADDR_3_TRIS = 1;
    // Enable the weak-pullup on the address pins
    I2C_ADDR_0_WPU = 1;
    I2C_ADDR_1_WPU = 1;
    I2C_ADDR_2_WPU = 1;
    I2C_ADDR_3_WPU = 1;

    // Initialize I2C pins (dont really need to as the I2C code does it)
    I2C_1_CLK_TRIS = 1;
    I2C_1_DAT_TRIS = 1;
    I2C_2_CLK_TRIS = 1;
    I2C_2_DAT_TRIS = 1;
}

uint8_t Read_Address(void) {
    uint8_t ret = 0;
    ret |= I2C_ADDR_3_LAT << 3;
    ret |= I2C_ADDR_2_LAT << 2;
    ret |= I2C_ADDR_1_LAT << 1;
    ret |= I2C_ADDR_0_LAT;
    
    return ret;
}

// Function to read button status into a data structure
void Pins_Read(BTN_STATUS *btns) {
    
}

// Function to write led values from the data structure
void Leds_Write(LED_STATUS *leds) {
    
}

int main(void) {
    uint8_t buffer[32];
    uint8_t result, length;
    uint8_t i2c_slave_addr;

    // Set internal oscillator speed to 32MHz
    OSCCONbits.SPLLEN = 1;  // 4x PLL enable (overwritten by config bits)
    OSCCONbits.IRCF = 0xE;  // Base frequency @ 8MHz
    OSCCONbits.SCS = 0b00;  // System clock determined by config bits

    // Set watchdog timer to reset device every 1s
    // CLRWDT is issued upon receiving data over I2C
//    WDTCON = 0x0A;

    // Initialize I/O
    Pins_Init();

    i2c_slave_addr = Read_Address();

    // Initialize I2C1 in slave mode
    I2C1_DATA i2c1_data;
    I2C1_Init(&i2c1_data);
    I2C1_Configure_Slave(i2c_slave_addr);

    // Initialize I2C2 in master mode
    I2C2_DATA i2c2_data;
    I2C2_Init(&i2c2_data);
    I2C2_Configure_Master(I2C_400KHZ);

    // Initialize interrupts
    Interrupt_Init();
    Interrupt_Enable();

    TLC59116_Init();

    uint8_t leds[16] = {0x00, 0x00, 0x00, 0x00,
                        0x00, 0x00, 0x00, 0x00,
                        0x10, 0x10, 0x10, 0x10,
                        0x10, 0x10, 0x10, 0x10};
    TLC59116_Write_All(leds);

    MCP23009_Init();

    // Check for received data over I2C
    while (1) {
        uint8_t btn_value = MCP23009_Query();
        uint8_t i;
        for (i = 0; i < 8; i++) {
            if ((btn_value >> i) & 0x1) {
                leds[i] = 0x00;
            } else {
                leds[i] = 0x10;
            }
        }
        TLC59116_Write_All(leds);


    }
}