Subversion Repositories Code-Repo

Rev

Rev 280 | Rev 282 | Go to most recent revision | Blame | Compare with Previous | Last modification | View Log | RSS feed

#include "defines.h"
#include "INTERRUPTS.h"
#include "I2C1.h"
#include "NEOPIXEL.h"
#include "DS3231.h"
#include "TSL2561.h"

// <editor-fold defaultstate="collapsed" desc="Configuration Registers">
/* Config Register CONFIGL @ 0x8007 */
#pragma config CPD = OFF    // Data memory code protection is disabled
#pragma config BOREN = OFF  // Brown-out Reset disabled
#pragma config IESO = OFF   // Internal/External Switchover mode is disabled
#pragma config FOSC = INTOSC    // INTOSC oscillator: I/O function on CLKIN pin
#pragma config FCMEN = OFF  // Fail-Safe Clock Monitor is disabled
#pragma config MCLRE = ON   // MCLR/VPP pin function is MCLR
#pragma config WDTE = OFF   // WDT disabled
#pragma config CP = OFF     // Program memory code protection is disabled
#pragma config PWRTE = OFF  // PWRT disabled
#pragma config CLKOUTEN = OFF   // CLKOUT function is disabled. I/O or oscillator function on the CLKOUT pin

/* Config Register CONFIG2 @ 0x8008 */
#pragma config PLLEN = ON   // 4x PLL disabled
#pragma config WRT = OFF    // Write protection off
#pragma config STVREN = OFF // Stack Overflow or Underflow will not cause a Reset
#pragma config BORV = HI    // Brown-out Reset Voltage (Vbor), high trip point selected.
#pragma config LVP = OFF    // High-voltage on MCLR/VPP must be used for programming
// </editor-fold>

I2C1_DATA i2c_data;
NEOPIXEL_DATA neopixel_data;
TSL2561_DATA tsl2561_data;
DS3231_TIME time;

int main() {
    // Oscillator configuration (32Mhz HFINTOSC)
    OSCCONbits.SCS = 0b00;
    OSCCONbits.IRCF = 0b1110;
    
    ANSELA = 0x00;  // All pins set to digital I/O
    APFCONbits.CCP1SEL = 1; // Switch CCP1 from RA2 to RA5

    // Wait for HFINTOSC to be within 0.5% of target 32Mhz
    while (!OSCSTATbits.HFIOFS);

    Interrupt_Enable();
    
    I2C1_Init();
    I2C1_Configure_Master(I2C_1MHZ);

    NeoPixel_Init();
    NeoPixel_Offet(30);

    DS3231_Init();

    TSL2561_Init(TSL2561_ADDR_FLOAT);

    // You can change the gain on the fly, to adapt to brighter/dimmer light situations
    TSL2561_Set_Gain(TSL2561_GAIN_0X);   // set no gain (for bright situtations)
//    TSL2561_Set_Gain(TSL2561_GAIN_16X);  // set 16x gain (for dim situations)

    // Changing the integration time gives you a longer time over which to sense light
    // longer timelines are slower, but are good in very low light situtations!
//    TSL2561_Set_Timing(TSL2561_INTEGRATIONTIME_13MS);  // shortest integration time (bright light)
    TSL2561_Set_Timing(TSL2561_INTEGRATIONTIME_101MS);  // medium integration time (medium light)
//    TSL2561_Set_Timing(TSL2561_INTEGRATIONTIME_402MS);  // longest integration time (dim light)

//    uint16_t full, ir, vis;

    while(1) {
//        full = TSL2561_Get_Luminosity(0);
//        ir = TSL2561_Get_Luminosity(1);
//        vis = full - ir;
//
//        NeoPixel_Clear();
//        for (uint8_t i = 0; i < (vis >> 11); i++) {
//            NeoPixel_Set(i, 0x10, 0x00, 0x00);
//        }
//        NeoPixel_Write_All();
//
//        __delay_ms(100);
        
        DS3231_Get_Time(&time);
        NeoPixel_Clear();

        // Draw markers
        NeoPixel_Set(0, 0x10, 0x00, 0x00);
        NeoPixel_Set(5, 0x08, 0x02, 0x00);
        NeoPixel_Set(10, 0x08, 0x08, 0x00);
        NeoPixel_Set(15, 0x00, 0x10, 0x00);
        NeoPixel_Set(20, 0x00, 0x00, 0x10);
        NeoPixel_Set(25, 0x08, 0x00, 0x08);
        NeoPixel_Set(30, 0x10, 0x00, 0x00);
        NeoPixel_Set(35, 0x08, 0x02, 0x00);
        NeoPixel_Set(40, 0x08, 0x08, 0x00);
        NeoPixel_Set(45, 0x00, 0x10, 0x00);
        NeoPixel_Set(50, 0x00, 0x00, 0x10);
        NeoPixel_Set(55, 0x08, 0x00, 0x08);

        // Draw time
        NeoPixel_Or((time.hour * 5) % 60, BLUE);
        NeoPixel_Or(time.min, GREEN);
        NeoPixel_Or(time.sec, RED);
        NeoPixel_Write_All();
    }
}