0,0 → 1,141 |
#include <xc.h> |
#include <delays.h> |
#include <stdio.h> |
#include "defines.h" |
#include "uart.h" |
|
// <editor-fold defaultstate="collapsed" desc="Configuration Bits"> |
/* --------------------------- Configuration Bits --------------------------- */ |
/* CONFIG1L @ 0x1FFF8 */ |
#pragma config CFGPLLEN = ON // Enable PLL on startup |
#pragma config PLLDIV = 3 // Set PPL prescaler to 3 (to get 4MHz) |
#pragma config WDTEN = OFF // Turn off watchdog timer |
#pragma config STVREN = OFF // Stack overflow/underflow reset disabled |
#pragma config XINST = OFF // Turn off extended instruction set |
|
/* CONFIG1H @ 0x1FFF9 */ |
#pragma config CP0 = OFF // Program memory is not code-protected |
|
/* CONFIG2L @ 0x1FFFA */ |
#pragma config CLKOEC = OFF // CLKO output disabled on RA6 pin |
#pragma config SOSCSEL = LOW // Low Power T1OSC/SOSC circuit selected |
#pragma config IESO = ON // Internal external oscillator switch over disabled |
#pragma config OSC = HSPLL // Use external oscillator (101) |
#pragma config FCMEN = OFF // Fail-safe clock monitor disabled |
|
/* CONFIG2H @ 0x1FFFB */ |
#pragma config WDTPS = 1 // Watchdog postscaler of 1:1 |
|
/* CONFIG3L @ 0x1FFFC */ |
#pragma config RTCOSC = T1OSCREF // RTCC uses T1OSC/T1CKI |
#pragma config DSBOREN = ON // Deep sleep BOR enabled |
#pragma config DSWDTPS = M2 // Deep sleep watchdog postscaler of 1:2 (36m) |
#pragma config DSWDTEN = OFF // Deep sleep watchdog timer disabled |
#pragma config DSWDTOSC = INTOSCREF // DSWDT clock select uses INTRC |
|
/* CONFIG3H @ 0x1FFFD */ |
#pragma config PLLSEL = PLL96 // Use 96MHz PLL 4MHz -> 96MHz / 2 = 48MHz |
#pragma config ADCSEL = BIT12 // 12-bit ADC |
#pragma config MSSP7B_EN = MSK7 // 7-bit address masking mode |
#pragma config IOL1WAY = OFF // IOLOCK bit can be set and cleared as needed |
|
/* CONFIG4L @ 0x1FFFE */ |
#pragma config WPCFG = ON // Configuration words page protected |
|
/* CONFIG4H @ 0x1FFFF */ |
#pragma config WPEND = PAGE_WPFP // Pages WPFP<6:0> through Configuration Words erase/write protected |
#pragma config WPDIS = OFF // WPFP<6:0>/WPEND region ignored |
/* -------------------------------------------------------------------------- */ |
// </editor-fold> |
|
#if defined(_TEST_UART) |
int main() { |
char buffer[100]; |
buffer[0] = 1; |
unsigned char length = 12345; |
unsigned char buffer[100]; |
float f = 3.1415; |
|
/* --------------------- Oscillator Configuration --------------------- */ |
// OSCTUNEbits.PLLEN = 1; // Enable 4x PLL |
OSCCONbits.IRCF = 0b111; // Set INTOSC postscaler to 8MHz |
OSCCONbits.SCS = 0b00; // Use 96MHz PLL as primary clock source |
/* -------------------------------------------------------------------- */ |
|
// Set all ports as digial I/O |
ANCON0 = 0xFF; |
ANCON1 = 0x1F; |
|
UART1_Init(); // Initialize the UART handler code |
|
// interrupt_enable(); // Enable high-priority interrupts and low-priority interrupts |
// interrupt_init(); // Initialize the interrupt priorities |
|
// DBG_PRINT_MAIN("\r\nBegin Program\r\n"); |
// DBG_PRINT_MAIN("%d\r\n", length); |
// printf("asf\r\n"); |
|
while (1) { |
|
// length = UART1_Read_Buffer((unsigned char *) buffer); |
// if (length != 0) { |
// UART1_WriteB((char *) buffer, length); |
// } |
// |
// Delay10KTCYx(255); |
// Delay10KTCYx(255); |
} |
} |
#elif defined(_TEST_I2C_MASTER) |
int main() { |
char buffer[100]; |
buffer[0] = 1; |
} |
#else |
int main() { |
char buffer[255]; |
char buffer1[255]; |
char buffer2[255]; |
char buffer3[255]; |
char buffer4[255]; |
char buffer5[255]; |
char buffer6[255]; |
char buffer7[255]; |
char buffer8[255]; |
char buffer9[255]; |
char buffer10[255]; |
char buffer11[255]; |
char buffer12[100]; |
char buffer13[100]; |
char buffer14[50]; |
char buffer15[50]; |
char buffer16[50]; |
char buffer17[40]; |
char buffer18[20]; |
buffer[0] = 1; |
buffer1[0] = 1; |
buffer2[0] = 1; |
buffer3[0] = 1; |
buffer4[0] = 1; |
buffer5[0] = 1; |
buffer6[0] = 1; |
buffer7[0] = 1; |
buffer8[0] = 1; |
buffer9[0] = 1; |
buffer10[0] = 1; |
buffer11[0] = 1; |
buffer12[0] = 1; |
buffer13[0] = 1; |
buffer14[0] = 1; |
buffer15[0] = 1; |
buffer16[0] = 1; |
buffer17[0] = 1; |
buffer18[0] = 1; |
} |
#endif |
|
void putch(char data) { |
while (!TXIF) |
continue; |
TXREG = data; |
} |