Subversion Repositories Code-Repo

Compare Revisions

Ignore whitespace Rev 161 → Rev 226

/PIC Stuff/PICX_27J13/base_SPI.c
117,6 → 117,38
#endif
}
 
void SPI2_DMA_Init(void) {
DMACON1bits.SSCON0 = 0;
DMACON1bits.SSCON1 = 0; // DYLINTEN is software programmable
 
DMACON1bits.TXINC = 1; // TXADDR is automatically incremented
DMACON1bits.RXINC = 0; // RXADDR is not automatically incremented
 
DMACON1bits.DUPLEX0 = 1;
DMACON1bits.DUPLEX1 = 0; // Half-duplex mode, transmission only
 
DMACON1bits.DLYINTEN = 0; // Interrupt is disabled
 
DMACON2bits.DLYCYC = 0b0000; // Delay time of 1 cycle between bytes
DMACON2bits.INTLVL = 0b0000; // Interrupt on transfer complete
}
 
void SPI2_DMA_Start(unsigned int length, void* TXADDR, void* RXADDR) {
// Set length of message to transmit
DMABCH = (char)(length-1 >> 8);
DMABCL = (char)(length-1);
 
// Set sourcing address
TXADDRH = (char)((int)TXADDR >> 8);
TXADDRL = (char)((int)TXADDR);
 
// Set receiving address
RXADDRH = (char)((int)RXADDR >> 8);
RXADDRL = (char)((int)RXADDR);
 
DMACON1bits.DMAEN = 1; // Start transmission
}
 
#ifndef SPI2_WRITE_ONLY
void SPI2_Recv_Interrupt_Handler() {
char c;
/PIC Stuff/PICX_27J13/base_SPI.h
10,6 → 10,7
//#define SPI2_USE_INTERRUPT
 
// SPI speed selection
#define SPI2_FOSC_TMR2 0b0011
#define SPI2_FOSC_64 0b0010
#define SPI2_FOSC_16 0b0001
#define SPI2_FOSC_8 0b1010
38,5 → 39,8
char SPI2_Read_Buffer(char *buffer);
#endif
 
void SPI2_DMA_Init(void);
void SPI2_DMA_Start(unsigned int length, void *TXADDR, void *RXADDR);
 
#endif /* SPI_H */
 
/PIC Stuff/PICX_27J13/defines.h
1,6 → 1,8
#ifndef DEFINES_H
#define DEFINES_H
 
#define _XTAL_FREQ 48000000
 
#define UART1_RX_TO_BUFFER
//#define UART1_RX_TO_XBEE
 
21,6 → 23,7
//#define _TEST_I2C_MASTER
//#define _TEST_I2C_SLAVE
//#define _TEST_SPI
#define _TEST_SPI_DMA
//#define _TEST_ADC
//#define _TEST_TIMER1_RTC
//#define _TEST_NFC
/PIC Stuff/PICX_27J13/funclist
1,110 → 1,25
_LED_Write_Digit_Num: CODE, 93530 0 102
_LED_Write_Num: CODE, 82386 0 724
___awdiv: CODE, 86204 0 322
_I2C_Get_Status: CODE, 89462 0 214
_LED_Write_Digit_Raw: CODE, 94384 0 80
_I2C_Interrupt_Master: CODE, 72930 0 1764
exp@coeff: MEDIUMCONST, 0 0 64563
_NFC_Send_Command_Check_Ack: CODE, 91320 0 144
_NFC_I2C_Read_Status: CODE, 95682 0 24
_LED_Init: CODE, 95706 0 22
_NFC_Init: CODE, 95748 0 12
_NHD_Write_String: CODE, 94206 0 92
_NFC_I2C_Read_ACK: CODE, 92522 0 118
_LUX_Enable: CODE, 95576 0 40
_LED_Set_Brightness: CODE, 91604 0 138
_DS3231_Begin: CODE, 91880 0 134
_NHD_Write_4_Bits: CODE, 91020 0 152
_I2C_Read_Buffer: CODE, 88536 0 238
__stringdata: MEDIUMCONST, 64605 0 929
_UART1_WriteS: CODE, 95018 0 64
_SSD1306_Set_Cursor: CODE, 95082 0 62
_SSD1306_Set_Rotation: CODE, 89010 0 234
_NHD_Init: CODE, 95616 0 36
_I2C_Interrupt_Slave: CODE, 71162 0 1768
_strlen: CODE, 93830 0 96
_NFC_SAMConfig: CODE, 90552 0 156
_I2C_Configure_Master: CODE, 94464 0 78
_LUX_Calculate_Lux: CODE, 76432 0 1422
_I2C_Master_Send: CODE, 88272 0 264
_SPI2_Init: CODE, 92402 0 120
_font: MEDIUMCONST, 63170 0 1275
_dpowers: MEDIUMCONST, 64445 0 40
_memset: CODE, 94954 0 64
___awmod: CODE, 87716 0 282
_UART1_Recv_Interrupt_Handler: CODE, 85352 0 428
_LED_Write_Display: CODE, 92146 0 128
_I2C_Master_Recv: CODE, 90708 0 156
_pn532response_firmwarevers: MEDIUMCONST, 64590 0 8
i2_isdigit: CODE, 95362 0 48
_main: CODE, 65536 0 3710
_LUX_Init: CODE, 94688 0 68
_Interrupt_Enable: CODE, 95780 0 8
_numbertable: MEDIUMCONST, 64517 0 10
_SSD1306_Draw_Fast_VLine: CODE, 93926 0 94
_NHD_Send_Command: CODE, 95456 0 40
_SSD1306_Abs: CODE, 95206 0 58
_NHD_Send_Data: CODE, 95496 0 40
_pn532ack: MEDIUMCONST, 64598 0 7
_LED_Start: CODE, 90222 0 166
_SSD1306_Swap: CODE, 94824 0 66
_SSD1306_Init: CODE, 87998 0 274
_LED_Draw_Colon: CODE, 94890 0 64
_I2C_Process_Send: CODE, 90388 0 164
i2___wmul: CODE, 95144 0 62
_NFC_I2C_Write_Cmd: CODE, 85780 0 424
_LUX_Read_2_Bytes: CODE, 91464 0 140
___lmul: CODE, 90054 0 168
_LUX_Write_2_Bytes: CODE, 94020 0 94
_I2C_Interrupt_Handler: CODE, 94616 0 72
_SSD1306_Write: CODE, 83802 0 592
_SSD1306_Begin: CODE, 83110 0 692
_NFC_I2C_Read_Data: CODE, 92640 0 118
_LED_Blink_Rate: CODE, 91172 0 148
i2___lldiv: CODE, 90864 0 156
_memcpy: CODE, 94298 0 86
_Interrupt_Init: CODE, 95760 0 10
__initialization: CODE, 93632 0 94
_SSD1306_Write_String: CODE, 94114 0 92
_DS3231_Get_Status: CODE, 92874 0 116
_NHD_Begin: CODE, 87430 0 286
_SSD1306_Draw_Line: CODE, 79940 0 862
_alphatable: MEDIUMCONST, 64527 0 6
_I2C_Master_Restart: CODE, 89244 0 218
_LUX_Set_Gain: CODE, 93102 0 110
___lldiv: CODE, 87142 0 288
_SSD1306_Draw_Char: CODE, 77854 0 1062
_SSD1306_Fill_Rect: CODE, 92014 0 132
_DS3231_Get_Time: CODE, 84394 0 480
_I2C_Init: CODE, 86844 0 298
_LED_Clear: CODE, 93732 0 98
_LUX_Disable: CODE, 95536 0 40
_NFC_Get_Firmware_Version: CODE, 86526 0 318
_isdigit: CODE, 94542 0 74
_sprintf: CODE, 69246 0 1916
_hexpowers: MEDIUMCONST, 64485 0 32
_NHD_Set_Cursor: CODE, 92758 0 116
_Delay10TCYx: CODE, 95728 0 20
i2___llmod: CODE, 92274 0 128
i2_sprintf: CODE, 74694 0 1738
_I2C_Interrupt_Master: CODE, 67304 0 1764
exp@coeff: MEDIUMCONST, 0 0 64687
_SPI2_DMA_Start: CODE, 71264 0 74
__stringdata: MEDIUMCONST, 64729 0 805
_UART1_WriteS: CODE, 71478 0 64
_I2C_Interrupt_Slave: CODE, 65536 0 1768
_strlen: CODE, 71410 0 68
_SPI2_Init: CODE, 70964 0 120
_font: MEDIUMCONST, 63366 0 1275
_UART1_Recv_Interrupt_Handler: CODE, 70092 0 428
_pn532response_firmwarevers: MEDIUMCONST, 64714 0 8
_main: CODE, 70684 0 142
_numbertable: MEDIUMCONST, 64641 0 10
_pn532ack: MEDIUMCONST, 64722 0 7
_I2C_Process_Send: CODE, 70520 0 164
_I2C_Interrupt_Handler: CODE, 71338 0 72
__initialization: CODE, 71084 0 90
_alphatable: MEDIUMCONST, 64651 0 6
_sprintf: CODE, 71180 0 84
_InterruptHandlerLow: CODE, 24 0 154
_Timer1_Interrupt_Handler: CODE, 95792 0 2
_Delay10KTCYx: CODE, 95652 0 30
_strncmp: CODE, 89676 0 208
_LUX_Set_Timing: CODE, 93212 0 110
_SSD1306_Clear_Display: CODE, 95264 0 50
_InterruptHandlerHigh: CODE, 8 0 91872
___llmod: CODE, 88774 0 236
log@coeff: MEDIUMCONST, 0 0 64590
_NHD_Wait_For_Ready: CODE, 95314 0 48
_SPI2_Write: CODE, 92990 0 112
_SSD1306_Command: CODE, 95410 0 46
i2_strlen: CODE, 94756 0 68
_memcmp: CODE, 89884 0 170
_SSD1306_Draw_Pixel: CODE, 81634 0 752
___wmul: CODE, 93426 0 104
_NFC_Poll_Targets: CODE, 80802 0 832
_SSD1306_Display: CODE, 93322 0 104
_LUX_Get_Full_Luminosity: CODE, 84874 0 478
_NHD_Pulse_Enable: CODE, 95770 0 10
Total: 252572
_Timer1_Interrupt_Handler: CODE, 71578 0 2
_InterruptHandlerHigh: CODE, 8 0 70956
log@coeff: MEDIUMCONST, 0 0 64714
_SPI2_DMA_Init: CODE, 71542 0 32
Total: 207494
/PIC Stuff/PICX_27J13/main.c
262,6 → 262,34
}
}
// </editor-fold>
#elif defined(_TEST_SPI_DMA)
// <editor-fold defaultstate="collapsed" desc="_TEST_SPI_DMA">
void main(void) {
char buffer[42];
char buffer2;
 
// Set all ports as digial I/O
ANCON0 = 0xFF;
ANCON1 = 0x1F;
 
SPI_DATA spi_data;
SPI2_Init(&spi_data, SPI2_FOSC_4); // Initialize the SPI module
SPI2_DMA_Init();
 
// Interrupt_Init(); // Initialize the interrupt priorities
// Interrupt_Enable(); // Enable high-priority interrupts and low-priority interrupts
 
// for (char i = 0; i < 42; i++) {
// buffer[i] = i;
// }
while (1) {
SPI2_DMA_Start(42, &buffer, &buffer2);
 
__delay_ms(1);
}
}
// </editor-fold>
#elif defined(_TEST_ADC)
// <editor-fold defaultstate="collapsed" desc="_TEST_ADC">
void main(void) {
/PIC Stuff/PICX_27J13/nbproject/Makefile-default.mk
75,7 → 75,7
${OBJECTDIR}/main.p1: main.c nbproject/Makefile-${CND_CONF}.mk
@${MKDIR} ${OBJECTDIR}
@${RM} ${OBJECTDIR}/main.p1.d
${MP_CC} --pass1 $(MP_EXTRA_CC_PRE) --chip=$(MP_PROCESSOR_OPTION) -Q -G --asmlist -D__DEBUG=1 --debugger=pickit3 --double=24 --float=24 --emi=wordwrite --opt=default,+asm,-asmfile,+speed,-space,-debug,9 --addrqual=ignore --mode=free -P -N255 --warn=0 --summary=default,-psect,-class,+mem,-hex,-file --runtime=default,+clear,+init,-keep,-no_startup,-download,+config,+clib,+plib "--errformat=%%f:%%l: error: %%s" "--warnformat=%%f:%%l: warning: %%s" "--msgformat=%%f:%%l: advisory: %%s" -o${OBJECTDIR}/main.p1 main.c
${MP_CC} --pass1 $(MP_EXTRA_CC_PRE) --chip=$(MP_PROCESSOR_OPTION) -Q -G --asmlist -D__DEBUG=1 --debugger=pickit3 --double=24 --float=24 --emi=wordwrite --opt=default,+asm,-asmfile,+speed,-space,-debug,9 --addrqual=ignore --mode=free -P -N255 --warn=0 --summary=default,-psect,-class,+mem,-hex,-file --output=default,-inhx032 --runtime=default,+clear,+init,-keep,-no_startup,-download,+config,+clib,+plib "--errformat=%%f:%%l: error: %%s" "--warnformat=%%f:%%l: warning: %%s" "--msgformat=%%f:%%l: advisory: %%s" -o${OBJECTDIR}/main.p1 main.c
@-${MV} ${OBJECTDIR}/main.d ${OBJECTDIR}/main.p1.d
@${FIXDEPS} ${OBJECTDIR}/main.p1.d $(SILENT) -rsi ${MP_CC_DIR}../
82,7 → 82,7
${OBJECTDIR}/base_UART.p1: base_UART.c nbproject/Makefile-${CND_CONF}.mk
@${MKDIR} ${OBJECTDIR}
@${RM} ${OBJECTDIR}/base_UART.p1.d
${MP_CC} --pass1 $(MP_EXTRA_CC_PRE) --chip=$(MP_PROCESSOR_OPTION) -Q -G --asmlist -D__DEBUG=1 --debugger=pickit3 --double=24 --float=24 --emi=wordwrite --opt=default,+asm,-asmfile,+speed,-space,-debug,9 --addrqual=ignore --mode=free -P -N255 --warn=0 --summary=default,-psect,-class,+mem,-hex,-file --runtime=default,+clear,+init,-keep,-no_startup,-download,+config,+clib,+plib "--errformat=%%f:%%l: error: %%s" "--warnformat=%%f:%%l: warning: %%s" "--msgformat=%%f:%%l: advisory: %%s" -o${OBJECTDIR}/base_UART.p1 base_UART.c
${MP_CC} --pass1 $(MP_EXTRA_CC_PRE) --chip=$(MP_PROCESSOR_OPTION) -Q -G --asmlist -D__DEBUG=1 --debugger=pickit3 --double=24 --float=24 --emi=wordwrite --opt=default,+asm,-asmfile,+speed,-space,-debug,9 --addrqual=ignore --mode=free -P -N255 --warn=0 --summary=default,-psect,-class,+mem,-hex,-file --output=default,-inhx032 --runtime=default,+clear,+init,-keep,-no_startup,-download,+config,+clib,+plib "--errformat=%%f:%%l: error: %%s" "--warnformat=%%f:%%l: warning: %%s" "--msgformat=%%f:%%l: advisory: %%s" -o${OBJECTDIR}/base_UART.p1 base_UART.c
@-${MV} ${OBJECTDIR}/base_UART.d ${OBJECTDIR}/base_UART.p1.d
@${FIXDEPS} ${OBJECTDIR}/base_UART.p1.d $(SILENT) -rsi ${MP_CC_DIR}../
89,7 → 89,7
${OBJECTDIR}/base_I2C.p1: base_I2C.c nbproject/Makefile-${CND_CONF}.mk
@${MKDIR} ${OBJECTDIR}
@${RM} ${OBJECTDIR}/base_I2C.p1.d
${MP_CC} --pass1 $(MP_EXTRA_CC_PRE) --chip=$(MP_PROCESSOR_OPTION) -Q -G --asmlist -D__DEBUG=1 --debugger=pickit3 --double=24 --float=24 --emi=wordwrite --opt=default,+asm,-asmfile,+speed,-space,-debug,9 --addrqual=ignore --mode=free -P -N255 --warn=0 --summary=default,-psect,-class,+mem,-hex,-file --runtime=default,+clear,+init,-keep,-no_startup,-download,+config,+clib,+plib "--errformat=%%f:%%l: error: %%s" "--warnformat=%%f:%%l: warning: %%s" "--msgformat=%%f:%%l: advisory: %%s" -o${OBJECTDIR}/base_I2C.p1 base_I2C.c
${MP_CC} --pass1 $(MP_EXTRA_CC_PRE) --chip=$(MP_PROCESSOR_OPTION) -Q -G --asmlist -D__DEBUG=1 --debugger=pickit3 --double=24 --float=24 --emi=wordwrite --opt=default,+asm,-asmfile,+speed,-space,-debug,9 --addrqual=ignore --mode=free -P -N255 --warn=0 --summary=default,-psect,-class,+mem,-hex,-file --output=default,-inhx032 --runtime=default,+clear,+init,-keep,-no_startup,-download,+config,+clib,+plib "--errformat=%%f:%%l: error: %%s" "--warnformat=%%f:%%l: warning: %%s" "--msgformat=%%f:%%l: advisory: %%s" -o${OBJECTDIR}/base_I2C.p1 base_I2C.c
@-${MV} ${OBJECTDIR}/base_I2C.d ${OBJECTDIR}/base_I2C.p1.d
@${FIXDEPS} ${OBJECTDIR}/base_I2C.p1.d $(SILENT) -rsi ${MP_CC_DIR}../
96,7 → 96,7
${OBJECTDIR}/base_SPI.p1: base_SPI.c nbproject/Makefile-${CND_CONF}.mk
@${MKDIR} ${OBJECTDIR}
@${RM} ${OBJECTDIR}/base_SPI.p1.d
${MP_CC} --pass1 $(MP_EXTRA_CC_PRE) --chip=$(MP_PROCESSOR_OPTION) -Q -G --asmlist -D__DEBUG=1 --debugger=pickit3 --double=24 --float=24 --emi=wordwrite --opt=default,+asm,-asmfile,+speed,-space,-debug,9 --addrqual=ignore --mode=free -P -N255 --warn=0 --summary=default,-psect,-class,+mem,-hex,-file --runtime=default,+clear,+init,-keep,-no_startup,-download,+config,+clib,+plib "--errformat=%%f:%%l: error: %%s" "--warnformat=%%f:%%l: warning: %%s" "--msgformat=%%f:%%l: advisory: %%s" -o${OBJECTDIR}/base_SPI.p1 base_SPI.c
${MP_CC} --pass1 $(MP_EXTRA_CC_PRE) --chip=$(MP_PROCESSOR_OPTION) -Q -G --asmlist -D__DEBUG=1 --debugger=pickit3 --double=24 --float=24 --emi=wordwrite --opt=default,+asm,-asmfile,+speed,-space,-debug,9 --addrqual=ignore --mode=free -P -N255 --warn=0 --summary=default,-psect,-class,+mem,-hex,-file --output=default,-inhx032 --runtime=default,+clear,+init,-keep,-no_startup,-download,+config,+clib,+plib "--errformat=%%f:%%l: error: %%s" "--warnformat=%%f:%%l: warning: %%s" "--msgformat=%%f:%%l: advisory: %%s" -o${OBJECTDIR}/base_SPI.p1 base_SPI.c
@-${MV} ${OBJECTDIR}/base_SPI.d ${OBJECTDIR}/base_SPI.p1.d
@${FIXDEPS} ${OBJECTDIR}/base_SPI.p1.d $(SILENT) -rsi ${MP_CC_DIR}../
103,7 → 103,7
${OBJECTDIR}/display_led_HT16K33.p1: display_led_HT16K33.c nbproject/Makefile-${CND_CONF}.mk
@${MKDIR} ${OBJECTDIR}
@${RM} ${OBJECTDIR}/display_led_HT16K33.p1.d
${MP_CC} --pass1 $(MP_EXTRA_CC_PRE) --chip=$(MP_PROCESSOR_OPTION) -Q -G --asmlist -D__DEBUG=1 --debugger=pickit3 --double=24 --float=24 --emi=wordwrite --opt=default,+asm,-asmfile,+speed,-space,-debug,9 --addrqual=ignore --mode=free -P -N255 --warn=0 --summary=default,-psect,-class,+mem,-hex,-file --runtime=default,+clear,+init,-keep,-no_startup,-download,+config,+clib,+plib "--errformat=%%f:%%l: error: %%s" "--warnformat=%%f:%%l: warning: %%s" "--msgformat=%%f:%%l: advisory: %%s" -o${OBJECTDIR}/display_led_HT16K33.p1 display_led_HT16K33.c
${MP_CC} --pass1 $(MP_EXTRA_CC_PRE) --chip=$(MP_PROCESSOR_OPTION) -Q -G --asmlist -D__DEBUG=1 --debugger=pickit3 --double=24 --float=24 --emi=wordwrite --opt=default,+asm,-asmfile,+speed,-space,-debug,9 --addrqual=ignore --mode=free -P -N255 --warn=0 --summary=default,-psect,-class,+mem,-hex,-file --output=default,-inhx032 --runtime=default,+clear,+init,-keep,-no_startup,-download,+config,+clib,+plib "--errformat=%%f:%%l: error: %%s" "--warnformat=%%f:%%l: warning: %%s" "--msgformat=%%f:%%l: advisory: %%s" -o${OBJECTDIR}/display_led_HT16K33.p1 display_led_HT16K33.c
@-${MV} ${OBJECTDIR}/display_led_HT16K33.d ${OBJECTDIR}/display_led_HT16K33.p1.d
@${FIXDEPS} ${OBJECTDIR}/display_led_HT16K33.p1.d $(SILENT) -rsi ${MP_CC_DIR}../
110,7 → 110,7
${OBJECTDIR}/sensor_nfc_PN532.p1: sensor_nfc_PN532.c nbproject/Makefile-${CND_CONF}.mk
@${MKDIR} ${OBJECTDIR}
@${RM} ${OBJECTDIR}/sensor_nfc_PN532.p1.d
${MP_CC} --pass1 $(MP_EXTRA_CC_PRE) --chip=$(MP_PROCESSOR_OPTION) -Q -G --asmlist -D__DEBUG=1 --debugger=pickit3 --double=24 --float=24 --emi=wordwrite --opt=default,+asm,-asmfile,+speed,-space,-debug,9 --addrqual=ignore --mode=free -P -N255 --warn=0 --summary=default,-psect,-class,+mem,-hex,-file --runtime=default,+clear,+init,-keep,-no_startup,-download,+config,+clib,+plib "--errformat=%%f:%%l: error: %%s" "--warnformat=%%f:%%l: warning: %%s" "--msgformat=%%f:%%l: advisory: %%s" -o${OBJECTDIR}/sensor_nfc_PN532.p1 sensor_nfc_PN532.c
${MP_CC} --pass1 $(MP_EXTRA_CC_PRE) --chip=$(MP_PROCESSOR_OPTION) -Q -G --asmlist -D__DEBUG=1 --debugger=pickit3 --double=24 --float=24 --emi=wordwrite --opt=default,+asm,-asmfile,+speed,-space,-debug,9 --addrqual=ignore --mode=free -P -N255 --warn=0 --summary=default,-psect,-class,+mem,-hex,-file --output=default,-inhx032 --runtime=default,+clear,+init,-keep,-no_startup,-download,+config,+clib,+plib "--errformat=%%f:%%l: error: %%s" "--warnformat=%%f:%%l: warning: %%s" "--msgformat=%%f:%%l: advisory: %%s" -o${OBJECTDIR}/sensor_nfc_PN532.p1 sensor_nfc_PN532.c
@-${MV} ${OBJECTDIR}/sensor_nfc_PN532.d ${OBJECTDIR}/sensor_nfc_PN532.p1.d
@${FIXDEPS} ${OBJECTDIR}/sensor_nfc_PN532.p1.d $(SILENT) -rsi ${MP_CC_DIR}../
117,7 → 117,7
${OBJECTDIR}/base_TIMERS.p1: base_TIMERS.c nbproject/Makefile-${CND_CONF}.mk
@${MKDIR} ${OBJECTDIR}
@${RM} ${OBJECTDIR}/base_TIMERS.p1.d
${MP_CC} --pass1 $(MP_EXTRA_CC_PRE) --chip=$(MP_PROCESSOR_OPTION) -Q -G --asmlist -D__DEBUG=1 --debugger=pickit3 --double=24 --float=24 --emi=wordwrite --opt=default,+asm,-asmfile,+speed,-space,-debug,9 --addrqual=ignore --mode=free -P -N255 --warn=0 --summary=default,-psect,-class,+mem,-hex,-file --runtime=default,+clear,+init,-keep,-no_startup,-download,+config,+clib,+plib "--errformat=%%f:%%l: error: %%s" "--warnformat=%%f:%%l: warning: %%s" "--msgformat=%%f:%%l: advisory: %%s" -o${OBJECTDIR}/base_TIMERS.p1 base_TIMERS.c
${MP_CC} --pass1 $(MP_EXTRA_CC_PRE) --chip=$(MP_PROCESSOR_OPTION) -Q -G --asmlist -D__DEBUG=1 --debugger=pickit3 --double=24 --float=24 --emi=wordwrite --opt=default,+asm,-asmfile,+speed,-space,-debug,9 --addrqual=ignore --mode=free -P -N255 --warn=0 --summary=default,-psect,-class,+mem,-hex,-file --output=default,-inhx032 --runtime=default,+clear,+init,-keep,-no_startup,-download,+config,+clib,+plib "--errformat=%%f:%%l: error: %%s" "--warnformat=%%f:%%l: warning: %%s" "--msgformat=%%f:%%l: advisory: %%s" -o${OBJECTDIR}/base_TIMERS.p1 base_TIMERS.c
@-${MV} ${OBJECTDIR}/base_TIMERS.d ${OBJECTDIR}/base_TIMERS.p1.d
@${FIXDEPS} ${OBJECTDIR}/base_TIMERS.p1.d $(SILENT) -rsi ${MP_CC_DIR}../
124,7 → 124,7
${OBJECTDIR}/comm_xbee.p1: comm_xbee.c nbproject/Makefile-${CND_CONF}.mk
@${MKDIR} ${OBJECTDIR}
@${RM} ${OBJECTDIR}/comm_xbee.p1.d
${MP_CC} --pass1 $(MP_EXTRA_CC_PRE) --chip=$(MP_PROCESSOR_OPTION) -Q -G --asmlist -D__DEBUG=1 --debugger=pickit3 --double=24 --float=24 --emi=wordwrite --opt=default,+asm,-asmfile,+speed,-space,-debug,9 --addrqual=ignore --mode=free -P -N255 --warn=0 --summary=default,-psect,-class,+mem,-hex,-file --runtime=default,+clear,+init,-keep,-no_startup,-download,+config,+clib,+plib "--errformat=%%f:%%l: error: %%s" "--warnformat=%%f:%%l: warning: %%s" "--msgformat=%%f:%%l: advisory: %%s" -o${OBJECTDIR}/comm_xbee.p1 comm_xbee.c
${MP_CC} --pass1 $(MP_EXTRA_CC_PRE) --chip=$(MP_PROCESSOR_OPTION) -Q -G --asmlist -D__DEBUG=1 --debugger=pickit3 --double=24 --float=24 --emi=wordwrite --opt=default,+asm,-asmfile,+speed,-space,-debug,9 --addrqual=ignore --mode=free -P -N255 --warn=0 --summary=default,-psect,-class,+mem,-hex,-file --output=default,-inhx032 --runtime=default,+clear,+init,-keep,-no_startup,-download,+config,+clib,+plib "--errformat=%%f:%%l: error: %%s" "--warnformat=%%f:%%l: warning: %%s" "--msgformat=%%f:%%l: advisory: %%s" -o${OBJECTDIR}/comm_xbee.p1 comm_xbee.c
@-${MV} ${OBJECTDIR}/comm_xbee.d ${OBJECTDIR}/comm_xbee.p1.d
@${FIXDEPS} ${OBJECTDIR}/comm_xbee.p1.d $(SILENT) -rsi ${MP_CC_DIR}../
131,7 → 131,7
${OBJECTDIR}/base_ADC.p1: base_ADC.c nbproject/Makefile-${CND_CONF}.mk
@${MKDIR} ${OBJECTDIR}
@${RM} ${OBJECTDIR}/base_ADC.p1.d
${MP_CC} --pass1 $(MP_EXTRA_CC_PRE) --chip=$(MP_PROCESSOR_OPTION) -Q -G --asmlist -D__DEBUG=1 --debugger=pickit3 --double=24 --float=24 --emi=wordwrite --opt=default,+asm,-asmfile,+speed,-space,-debug,9 --addrqual=ignore --mode=free -P -N255 --warn=0 --summary=default,-psect,-class,+mem,-hex,-file --runtime=default,+clear,+init,-keep,-no_startup,-download,+config,+clib,+plib "--errformat=%%f:%%l: error: %%s" "--warnformat=%%f:%%l: warning: %%s" "--msgformat=%%f:%%l: advisory: %%s" -o${OBJECTDIR}/base_ADC.p1 base_ADC.c
${MP_CC} --pass1 $(MP_EXTRA_CC_PRE) --chip=$(MP_PROCESSOR_OPTION) -Q -G --asmlist -D__DEBUG=1 --debugger=pickit3 --double=24 --float=24 --emi=wordwrite --opt=default,+asm,-asmfile,+speed,-space,-debug,9 --addrqual=ignore --mode=free -P -N255 --warn=0 --summary=default,-psect,-class,+mem,-hex,-file --output=default,-inhx032 --runtime=default,+clear,+init,-keep,-no_startup,-download,+config,+clib,+plib "--errformat=%%f:%%l: error: %%s" "--warnformat=%%f:%%l: warning: %%s" "--msgformat=%%f:%%l: advisory: %%s" -o${OBJECTDIR}/base_ADC.p1 base_ADC.c
@-${MV} ${OBJECTDIR}/base_ADC.d ${OBJECTDIR}/base_ADC.p1.d
@${FIXDEPS} ${OBJECTDIR}/base_ADC.p1.d $(SILENT) -rsi ${MP_CC_DIR}../
138,7 → 138,7
${OBJECTDIR}/base_INTERRUPTS.p1: base_INTERRUPTS.c nbproject/Makefile-${CND_CONF}.mk
@${MKDIR} ${OBJECTDIR}
@${RM} ${OBJECTDIR}/base_INTERRUPTS.p1.d
${MP_CC} --pass1 $(MP_EXTRA_CC_PRE) --chip=$(MP_PROCESSOR_OPTION) -Q -G --asmlist -D__DEBUG=1 --debugger=pickit3 --double=24 --float=24 --emi=wordwrite --opt=default,+asm,-asmfile,+speed,-space,-debug,9 --addrqual=ignore --mode=free -P -N255 --warn=0 --summary=default,-psect,-class,+mem,-hex,-file --runtime=default,+clear,+init,-keep,-no_startup,-download,+config,+clib,+plib "--errformat=%%f:%%l: error: %%s" "--warnformat=%%f:%%l: warning: %%s" "--msgformat=%%f:%%l: advisory: %%s" -o${OBJECTDIR}/base_INTERRUPTS.p1 base_INTERRUPTS.c
${MP_CC} --pass1 $(MP_EXTRA_CC_PRE) --chip=$(MP_PROCESSOR_OPTION) -Q -G --asmlist -D__DEBUG=1 --debugger=pickit3 --double=24 --float=24 --emi=wordwrite --opt=default,+asm,-asmfile,+speed,-space,-debug,9 --addrqual=ignore --mode=free -P -N255 --warn=0 --summary=default,-psect,-class,+mem,-hex,-file --output=default,-inhx032 --runtime=default,+clear,+init,-keep,-no_startup,-download,+config,+clib,+plib "--errformat=%%f:%%l: error: %%s" "--warnformat=%%f:%%l: warning: %%s" "--msgformat=%%f:%%l: advisory: %%s" -o${OBJECTDIR}/base_INTERRUPTS.p1 base_INTERRUPTS.c
@-${MV} ${OBJECTDIR}/base_INTERRUPTS.d ${OBJECTDIR}/base_INTERRUPTS.p1.d
@${FIXDEPS} ${OBJECTDIR}/base_INTERRUPTS.p1.d $(SILENT) -rsi ${MP_CC_DIR}../
145,7 → 145,7
${OBJECTDIR}/display_oled_NHD-0216KZW-AB5.p1: display_oled_NHD-0216KZW-AB5.c nbproject/Makefile-${CND_CONF}.mk
@${MKDIR} ${OBJECTDIR}
@${RM} ${OBJECTDIR}/display_oled_NHD-0216KZW-AB5.p1.d
${MP_CC} --pass1 $(MP_EXTRA_CC_PRE) --chip=$(MP_PROCESSOR_OPTION) -Q -G --asmlist -D__DEBUG=1 --debugger=pickit3 --double=24 --float=24 --emi=wordwrite --opt=default,+asm,-asmfile,+speed,-space,-debug,9 --addrqual=ignore --mode=free -P -N255 --warn=0 --summary=default,-psect,-class,+mem,-hex,-file --runtime=default,+clear,+init,-keep,-no_startup,-download,+config,+clib,+plib "--errformat=%%f:%%l: error: %%s" "--warnformat=%%f:%%l: warning: %%s" "--msgformat=%%f:%%l: advisory: %%s" -o${OBJECTDIR}/display_oled_NHD-0216KZW-AB5.p1 display_oled_NHD-0216KZW-AB5.c
${MP_CC} --pass1 $(MP_EXTRA_CC_PRE) --chip=$(MP_PROCESSOR_OPTION) -Q -G --asmlist -D__DEBUG=1 --debugger=pickit3 --double=24 --float=24 --emi=wordwrite --opt=default,+asm,-asmfile,+speed,-space,-debug,9 --addrqual=ignore --mode=free -P -N255 --warn=0 --summary=default,-psect,-class,+mem,-hex,-file --output=default,-inhx032 --runtime=default,+clear,+init,-keep,-no_startup,-download,+config,+clib,+plib "--errformat=%%f:%%l: error: %%s" "--warnformat=%%f:%%l: warning: %%s" "--msgformat=%%f:%%l: advisory: %%s" -o${OBJECTDIR}/display_oled_NHD-0216KZW-AB5.p1 display_oled_NHD-0216KZW-AB5.c
@-${MV} ${OBJECTDIR}/display_oled_NHD-0216KZW-AB5.d ${OBJECTDIR}/display_oled_NHD-0216KZW-AB5.p1.d
@${FIXDEPS} ${OBJECTDIR}/display_oled_NHD-0216KZW-AB5.p1.d $(SILENT) -rsi ${MP_CC_DIR}../
152,7 → 152,7
${OBJECTDIR}/display_oled_ssd1306.p1: display_oled_ssd1306.c nbproject/Makefile-${CND_CONF}.mk
@${MKDIR} ${OBJECTDIR}
@${RM} ${OBJECTDIR}/display_oled_ssd1306.p1.d
${MP_CC} --pass1 $(MP_EXTRA_CC_PRE) --chip=$(MP_PROCESSOR_OPTION) -Q -G --asmlist -D__DEBUG=1 --debugger=pickit3 --double=24 --float=24 --emi=wordwrite --opt=default,+asm,-asmfile,+speed,-space,-debug,9 --addrqual=ignore --mode=free -P -N255 --warn=0 --summary=default,-psect,-class,+mem,-hex,-file --runtime=default,+clear,+init,-keep,-no_startup,-download,+config,+clib,+plib "--errformat=%%f:%%l: error: %%s" "--warnformat=%%f:%%l: warning: %%s" "--msgformat=%%f:%%l: advisory: %%s" -o${OBJECTDIR}/display_oled_ssd1306.p1 display_oled_ssd1306.c
${MP_CC} --pass1 $(MP_EXTRA_CC_PRE) --chip=$(MP_PROCESSOR_OPTION) -Q -G --asmlist -D__DEBUG=1 --debugger=pickit3 --double=24 --float=24 --emi=wordwrite --opt=default,+asm,-asmfile,+speed,-space,-debug,9 --addrqual=ignore --mode=free -P -N255 --warn=0 --summary=default,-psect,-class,+mem,-hex,-file --output=default,-inhx032 --runtime=default,+clear,+init,-keep,-no_startup,-download,+config,+clib,+plib "--errformat=%%f:%%l: error: %%s" "--warnformat=%%f:%%l: warning: %%s" "--msgformat=%%f:%%l: advisory: %%s" -o${OBJECTDIR}/display_oled_ssd1306.p1 display_oled_ssd1306.c
@-${MV} ${OBJECTDIR}/display_oled_ssd1306.d ${OBJECTDIR}/display_oled_ssd1306.p1.d
@${FIXDEPS} ${OBJECTDIR}/display_oled_ssd1306.p1.d $(SILENT) -rsi ${MP_CC_DIR}../
159,7 → 159,7
${OBJECTDIR}/display_oled_ssd1331.p1: display_oled_ssd1331.c nbproject/Makefile-${CND_CONF}.mk
@${MKDIR} ${OBJECTDIR}
@${RM} ${OBJECTDIR}/display_oled_ssd1331.p1.d
${MP_CC} --pass1 $(MP_EXTRA_CC_PRE) --chip=$(MP_PROCESSOR_OPTION) -Q -G --asmlist -D__DEBUG=1 --debugger=pickit3 --double=24 --float=24 --emi=wordwrite --opt=default,+asm,-asmfile,+speed,-space,-debug,9 --addrqual=ignore --mode=free -P -N255 --warn=0 --summary=default,-psect,-class,+mem,-hex,-file --runtime=default,+clear,+init,-keep,-no_startup,-download,+config,+clib,+plib "--errformat=%%f:%%l: error: %%s" "--warnformat=%%f:%%l: warning: %%s" "--msgformat=%%f:%%l: advisory: %%s" -o${OBJECTDIR}/display_oled_ssd1331.p1 display_oled_ssd1331.c
${MP_CC} --pass1 $(MP_EXTRA_CC_PRE) --chip=$(MP_PROCESSOR_OPTION) -Q -G --asmlist -D__DEBUG=1 --debugger=pickit3 --double=24 --float=24 --emi=wordwrite --opt=default,+asm,-asmfile,+speed,-space,-debug,9 --addrqual=ignore --mode=free -P -N255 --warn=0 --summary=default,-psect,-class,+mem,-hex,-file --output=default,-inhx032 --runtime=default,+clear,+init,-keep,-no_startup,-download,+config,+clib,+plib "--errformat=%%f:%%l: error: %%s" "--warnformat=%%f:%%l: warning: %%s" "--msgformat=%%f:%%l: advisory: %%s" -o${OBJECTDIR}/display_oled_ssd1331.p1 display_oled_ssd1331.c
@-${MV} ${OBJECTDIR}/display_oled_ssd1331.d ${OBJECTDIR}/display_oled_ssd1331.p1.d
@${FIXDEPS} ${OBJECTDIR}/display_oled_ssd1331.p1.d $(SILENT) -rsi ${MP_CC_DIR}../
166,7 → 166,7
${OBJECTDIR}/glcdfont.p1: glcdfont.c nbproject/Makefile-${CND_CONF}.mk
@${MKDIR} ${OBJECTDIR}
@${RM} ${OBJECTDIR}/glcdfont.p1.d
${MP_CC} --pass1 $(MP_EXTRA_CC_PRE) --chip=$(MP_PROCESSOR_OPTION) -Q -G --asmlist -D__DEBUG=1 --debugger=pickit3 --double=24 --float=24 --emi=wordwrite --opt=default,+asm,-asmfile,+speed,-space,-debug,9 --addrqual=ignore --mode=free -P -N255 --warn=0 --summary=default,-psect,-class,+mem,-hex,-file --runtime=default,+clear,+init,-keep,-no_startup,-download,+config,+clib,+plib "--errformat=%%f:%%l: error: %%s" "--warnformat=%%f:%%l: warning: %%s" "--msgformat=%%f:%%l: advisory: %%s" -o${OBJECTDIR}/glcdfont.p1 glcdfont.c
${MP_CC} --pass1 $(MP_EXTRA_CC_PRE) --chip=$(MP_PROCESSOR_OPTION) -Q -G --asmlist -D__DEBUG=1 --debugger=pickit3 --double=24 --float=24 --emi=wordwrite --opt=default,+asm,-asmfile,+speed,-space,-debug,9 --addrqual=ignore --mode=free -P -N255 --warn=0 --summary=default,-psect,-class,+mem,-hex,-file --output=default,-inhx032 --runtime=default,+clear,+init,-keep,-no_startup,-download,+config,+clib,+plib "--errformat=%%f:%%l: error: %%s" "--warnformat=%%f:%%l: warning: %%s" "--msgformat=%%f:%%l: advisory: %%s" -o${OBJECTDIR}/glcdfont.p1 glcdfont.c
@-${MV} ${OBJECTDIR}/glcdfont.d ${OBJECTDIR}/glcdfont.p1.d
@${FIXDEPS} ${OBJECTDIR}/glcdfont.p1.d $(SILENT) -rsi ${MP_CC_DIR}../
173,7 → 173,7
${OBJECTDIR}/sensor_lux_TSL2561.p1: sensor_lux_TSL2561.c nbproject/Makefile-${CND_CONF}.mk
@${MKDIR} ${OBJECTDIR}
@${RM} ${OBJECTDIR}/sensor_lux_TSL2561.p1.d
${MP_CC} --pass1 $(MP_EXTRA_CC_PRE) --chip=$(MP_PROCESSOR_OPTION) -Q -G --asmlist -D__DEBUG=1 --debugger=pickit3 --double=24 --float=24 --emi=wordwrite --opt=default,+asm,-asmfile,+speed,-space,-debug,9 --addrqual=ignore --mode=free -P -N255 --warn=0 --summary=default,-psect,-class,+mem,-hex,-file --runtime=default,+clear,+init,-keep,-no_startup,-download,+config,+clib,+plib "--errformat=%%f:%%l: error: %%s" "--warnformat=%%f:%%l: warning: %%s" "--msgformat=%%f:%%l: advisory: %%s" -o${OBJECTDIR}/sensor_lux_TSL2561.p1 sensor_lux_TSL2561.c
${MP_CC} --pass1 $(MP_EXTRA_CC_PRE) --chip=$(MP_PROCESSOR_OPTION) -Q -G --asmlist -D__DEBUG=1 --debugger=pickit3 --double=24 --float=24 --emi=wordwrite --opt=default,+asm,-asmfile,+speed,-space,-debug,9 --addrqual=ignore --mode=free -P -N255 --warn=0 --summary=default,-psect,-class,+mem,-hex,-file --output=default,-inhx032 --runtime=default,+clear,+init,-keep,-no_startup,-download,+config,+clib,+plib "--errformat=%%f:%%l: error: %%s" "--warnformat=%%f:%%l: warning: %%s" "--msgformat=%%f:%%l: advisory: %%s" -o${OBJECTDIR}/sensor_lux_TSL2561.p1 sensor_lux_TSL2561.c
@-${MV} ${OBJECTDIR}/sensor_lux_TSL2561.d ${OBJECTDIR}/sensor_lux_TSL2561.p1.d
@${FIXDEPS} ${OBJECTDIR}/sensor_lux_TSL2561.p1.d $(SILENT) -rsi ${MP_CC_DIR}../
180,7 → 180,7
${OBJECTDIR}/sensor_temp_BMP085.p1: sensor_temp_BMP085.c nbproject/Makefile-${CND_CONF}.mk
@${MKDIR} ${OBJECTDIR}
@${RM} ${OBJECTDIR}/sensor_temp_BMP085.p1.d
${MP_CC} --pass1 $(MP_EXTRA_CC_PRE) --chip=$(MP_PROCESSOR_OPTION) -Q -G --asmlist -D__DEBUG=1 --debugger=pickit3 --double=24 --float=24 --emi=wordwrite --opt=default,+asm,-asmfile,+speed,-space,-debug,9 --addrqual=ignore --mode=free -P -N255 --warn=0 --summary=default,-psect,-class,+mem,-hex,-file --runtime=default,+clear,+init,-keep,-no_startup,-download,+config,+clib,+plib "--errformat=%%f:%%l: error: %%s" "--warnformat=%%f:%%l: warning: %%s" "--msgformat=%%f:%%l: advisory: %%s" -o${OBJECTDIR}/sensor_temp_BMP085.p1 sensor_temp_BMP085.c
${MP_CC} --pass1 $(MP_EXTRA_CC_PRE) --chip=$(MP_PROCESSOR_OPTION) -Q -G --asmlist -D__DEBUG=1 --debugger=pickit3 --double=24 --float=24 --emi=wordwrite --opt=default,+asm,-asmfile,+speed,-space,-debug,9 --addrqual=ignore --mode=free -P -N255 --warn=0 --summary=default,-psect,-class,+mem,-hex,-file --output=default,-inhx032 --runtime=default,+clear,+init,-keep,-no_startup,-download,+config,+clib,+plib "--errformat=%%f:%%l: error: %%s" "--warnformat=%%f:%%l: warning: %%s" "--msgformat=%%f:%%l: advisory: %%s" -o${OBJECTDIR}/sensor_temp_BMP085.p1 sensor_temp_BMP085.c
@-${MV} ${OBJECTDIR}/sensor_temp_BMP085.d ${OBJECTDIR}/sensor_temp_BMP085.p1.d
@${FIXDEPS} ${OBJECTDIR}/sensor_temp_BMP085.p1.d $(SILENT) -rsi ${MP_CC_DIR}../
187,7 → 187,7
${OBJECTDIR}/sensor_gyro_L3G.p1: sensor_gyro_L3G.c nbproject/Makefile-${CND_CONF}.mk
@${MKDIR} ${OBJECTDIR}
@${RM} ${OBJECTDIR}/sensor_gyro_L3G.p1.d
${MP_CC} --pass1 $(MP_EXTRA_CC_PRE) --chip=$(MP_PROCESSOR_OPTION) -Q -G --asmlist -D__DEBUG=1 --debugger=pickit3 --double=24 --float=24 --emi=wordwrite --opt=default,+asm,-asmfile,+speed,-space,-debug,9 --addrqual=ignore --mode=free -P -N255 --warn=0 --summary=default,-psect,-class,+mem,-hex,-file --runtime=default,+clear,+init,-keep,-no_startup,-download,+config,+clib,+plib "--errformat=%%f:%%l: error: %%s" "--warnformat=%%f:%%l: warning: %%s" "--msgformat=%%f:%%l: advisory: %%s" -o${OBJECTDIR}/sensor_gyro_L3G.p1 sensor_gyro_L3G.c
${MP_CC} --pass1 $(MP_EXTRA_CC_PRE) --chip=$(MP_PROCESSOR_OPTION) -Q -G --asmlist -D__DEBUG=1 --debugger=pickit3 --double=24 --float=24 --emi=wordwrite --opt=default,+asm,-asmfile,+speed,-space,-debug,9 --addrqual=ignore --mode=free -P -N255 --warn=0 --summary=default,-psect,-class,+mem,-hex,-file --output=default,-inhx032 --runtime=default,+clear,+init,-keep,-no_startup,-download,+config,+clib,+plib "--errformat=%%f:%%l: error: %%s" "--warnformat=%%f:%%l: warning: %%s" "--msgformat=%%f:%%l: advisory: %%s" -o${OBJECTDIR}/sensor_gyro_L3G.p1 sensor_gyro_L3G.c
@-${MV} ${OBJECTDIR}/sensor_gyro_L3G.d ${OBJECTDIR}/sensor_gyro_L3G.p1.d
@${FIXDEPS} ${OBJECTDIR}/sensor_gyro_L3G.p1.d $(SILENT) -rsi ${MP_CC_DIR}../
194,7 → 194,7
${OBJECTDIR}/sensor_accel_LSM303.p1: sensor_accel_LSM303.c nbproject/Makefile-${CND_CONF}.mk
@${MKDIR} ${OBJECTDIR}
@${RM} ${OBJECTDIR}/sensor_accel_LSM303.p1.d
${MP_CC} --pass1 $(MP_EXTRA_CC_PRE) --chip=$(MP_PROCESSOR_OPTION) -Q -G --asmlist -D__DEBUG=1 --debugger=pickit3 --double=24 --float=24 --emi=wordwrite --opt=default,+asm,-asmfile,+speed,-space,-debug,9 --addrqual=ignore --mode=free -P -N255 --warn=0 --summary=default,-psect,-class,+mem,-hex,-file --runtime=default,+clear,+init,-keep,-no_startup,-download,+config,+clib,+plib "--errformat=%%f:%%l: error: %%s" "--warnformat=%%f:%%l: warning: %%s" "--msgformat=%%f:%%l: advisory: %%s" -o${OBJECTDIR}/sensor_accel_LSM303.p1 sensor_accel_LSM303.c
${MP_CC} --pass1 $(MP_EXTRA_CC_PRE) --chip=$(MP_PROCESSOR_OPTION) -Q -G --asmlist -D__DEBUG=1 --debugger=pickit3 --double=24 --float=24 --emi=wordwrite --opt=default,+asm,-asmfile,+speed,-space,-debug,9 --addrqual=ignore --mode=free -P -N255 --warn=0 --summary=default,-psect,-class,+mem,-hex,-file --output=default,-inhx032 --runtime=default,+clear,+init,-keep,-no_startup,-download,+config,+clib,+plib "--errformat=%%f:%%l: error: %%s" "--warnformat=%%f:%%l: warning: %%s" "--msgformat=%%f:%%l: advisory: %%s" -o${OBJECTDIR}/sensor_accel_LSM303.p1 sensor_accel_LSM303.c
@-${MV} ${OBJECTDIR}/sensor_accel_LSM303.d ${OBJECTDIR}/sensor_accel_LSM303.p1.d
@${FIXDEPS} ${OBJECTDIR}/sensor_accel_LSM303.p1.d $(SILENT) -rsi ${MP_CC_DIR}../
201,7 → 201,7
${OBJECTDIR}/sensor_rtc_DS3231.p1: sensor_rtc_DS3231.c nbproject/Makefile-${CND_CONF}.mk
@${MKDIR} ${OBJECTDIR}
@${RM} ${OBJECTDIR}/sensor_rtc_DS3231.p1.d
${MP_CC} --pass1 $(MP_EXTRA_CC_PRE) --chip=$(MP_PROCESSOR_OPTION) -Q -G --asmlist -D__DEBUG=1 --debugger=pickit3 --double=24 --float=24 --emi=wordwrite --opt=default,+asm,-asmfile,+speed,-space,-debug,9 --addrqual=ignore --mode=free -P -N255 --warn=0 --summary=default,-psect,-class,+mem,-hex,-file --runtime=default,+clear,+init,-keep,-no_startup,-download,+config,+clib,+plib "--errformat=%%f:%%l: error: %%s" "--warnformat=%%f:%%l: warning: %%s" "--msgformat=%%f:%%l: advisory: %%s" -o${OBJECTDIR}/sensor_rtc_DS3231.p1 sensor_rtc_DS3231.c
${MP_CC} --pass1 $(MP_EXTRA_CC_PRE) --chip=$(MP_PROCESSOR_OPTION) -Q -G --asmlist -D__DEBUG=1 --debugger=pickit3 --double=24 --float=24 --emi=wordwrite --opt=default,+asm,-asmfile,+speed,-space,-debug,9 --addrqual=ignore --mode=free -P -N255 --warn=0 --summary=default,-psect,-class,+mem,-hex,-file --output=default,-inhx032 --runtime=default,+clear,+init,-keep,-no_startup,-download,+config,+clib,+plib "--errformat=%%f:%%l: error: %%s" "--warnformat=%%f:%%l: warning: %%s" "--msgformat=%%f:%%l: advisory: %%s" -o${OBJECTDIR}/sensor_rtc_DS3231.p1 sensor_rtc_DS3231.c
@-${MV} ${OBJECTDIR}/sensor_rtc_DS3231.d ${OBJECTDIR}/sensor_rtc_DS3231.p1.d
@${FIXDEPS} ${OBJECTDIR}/sensor_rtc_DS3231.p1.d $(SILENT) -rsi ${MP_CC_DIR}../
209,7 → 209,7
${OBJECTDIR}/main.p1: main.c nbproject/Makefile-${CND_CONF}.mk
@${MKDIR} ${OBJECTDIR}
@${RM} ${OBJECTDIR}/main.p1.d
${MP_CC} --pass1 $(MP_EXTRA_CC_PRE) --chip=$(MP_PROCESSOR_OPTION) -Q -G --asmlist --double=24 --float=24 --emi=wordwrite --opt=default,+asm,-asmfile,+speed,-space,-debug,9 --addrqual=ignore --mode=free -P -N255 --warn=0 --summary=default,-psect,-class,+mem,-hex,-file --runtime=default,+clear,+init,-keep,-no_startup,-download,+config,+clib,+plib "--errformat=%%f:%%l: error: %%s" "--warnformat=%%f:%%l: warning: %%s" "--msgformat=%%f:%%l: advisory: %%s" -o${OBJECTDIR}/main.p1 main.c
${MP_CC} --pass1 $(MP_EXTRA_CC_PRE) --chip=$(MP_PROCESSOR_OPTION) -Q -G --asmlist --double=24 --float=24 --emi=wordwrite --opt=default,+asm,-asmfile,+speed,-space,-debug,9 --addrqual=ignore --mode=free -P -N255 --warn=0 --summary=default,-psect,-class,+mem,-hex,-file --output=default,-inhx032 --runtime=default,+clear,+init,-keep,-no_startup,-download,+config,+clib,+plib "--errformat=%%f:%%l: error: %%s" "--warnformat=%%f:%%l: warning: %%s" "--msgformat=%%f:%%l: advisory: %%s" -o${OBJECTDIR}/main.p1 main.c
@-${MV} ${OBJECTDIR}/main.d ${OBJECTDIR}/main.p1.d
@${FIXDEPS} ${OBJECTDIR}/main.p1.d $(SILENT) -rsi ${MP_CC_DIR}../
216,7 → 216,7
${OBJECTDIR}/base_UART.p1: base_UART.c nbproject/Makefile-${CND_CONF}.mk
@${MKDIR} ${OBJECTDIR}
@${RM} ${OBJECTDIR}/base_UART.p1.d
${MP_CC} --pass1 $(MP_EXTRA_CC_PRE) --chip=$(MP_PROCESSOR_OPTION) -Q -G --asmlist --double=24 --float=24 --emi=wordwrite --opt=default,+asm,-asmfile,+speed,-space,-debug,9 --addrqual=ignore --mode=free -P -N255 --warn=0 --summary=default,-psect,-class,+mem,-hex,-file --runtime=default,+clear,+init,-keep,-no_startup,-download,+config,+clib,+plib "--errformat=%%f:%%l: error: %%s" "--warnformat=%%f:%%l: warning: %%s" "--msgformat=%%f:%%l: advisory: %%s" -o${OBJECTDIR}/base_UART.p1 base_UART.c
${MP_CC} --pass1 $(MP_EXTRA_CC_PRE) --chip=$(MP_PROCESSOR_OPTION) -Q -G --asmlist --double=24 --float=24 --emi=wordwrite --opt=default,+asm,-asmfile,+speed,-space,-debug,9 --addrqual=ignore --mode=free -P -N255 --warn=0 --summary=default,-psect,-class,+mem,-hex,-file --output=default,-inhx032 --runtime=default,+clear,+init,-keep,-no_startup,-download,+config,+clib,+plib "--errformat=%%f:%%l: error: %%s" "--warnformat=%%f:%%l: warning: %%s" "--msgformat=%%f:%%l: advisory: %%s" -o${OBJECTDIR}/base_UART.p1 base_UART.c
@-${MV} ${OBJECTDIR}/base_UART.d ${OBJECTDIR}/base_UART.p1.d
@${FIXDEPS} ${OBJECTDIR}/base_UART.p1.d $(SILENT) -rsi ${MP_CC_DIR}../
223,7 → 223,7
${OBJECTDIR}/base_I2C.p1: base_I2C.c nbproject/Makefile-${CND_CONF}.mk
@${MKDIR} ${OBJECTDIR}
@${RM} ${OBJECTDIR}/base_I2C.p1.d
${MP_CC} --pass1 $(MP_EXTRA_CC_PRE) --chip=$(MP_PROCESSOR_OPTION) -Q -G --asmlist --double=24 --float=24 --emi=wordwrite --opt=default,+asm,-asmfile,+speed,-space,-debug,9 --addrqual=ignore --mode=free -P -N255 --warn=0 --summary=default,-psect,-class,+mem,-hex,-file --runtime=default,+clear,+init,-keep,-no_startup,-download,+config,+clib,+plib "--errformat=%%f:%%l: error: %%s" "--warnformat=%%f:%%l: warning: %%s" "--msgformat=%%f:%%l: advisory: %%s" -o${OBJECTDIR}/base_I2C.p1 base_I2C.c
${MP_CC} --pass1 $(MP_EXTRA_CC_PRE) --chip=$(MP_PROCESSOR_OPTION) -Q -G --asmlist --double=24 --float=24 --emi=wordwrite --opt=default,+asm,-asmfile,+speed,-space,-debug,9 --addrqual=ignore --mode=free -P -N255 --warn=0 --summary=default,-psect,-class,+mem,-hex,-file --output=default,-inhx032 --runtime=default,+clear,+init,-keep,-no_startup,-download,+config,+clib,+plib "--errformat=%%f:%%l: error: %%s" "--warnformat=%%f:%%l: warning: %%s" "--msgformat=%%f:%%l: advisory: %%s" -o${OBJECTDIR}/base_I2C.p1 base_I2C.c
@-${MV} ${OBJECTDIR}/base_I2C.d ${OBJECTDIR}/base_I2C.p1.d
@${FIXDEPS} ${OBJECTDIR}/base_I2C.p1.d $(SILENT) -rsi ${MP_CC_DIR}../
230,7 → 230,7
${OBJECTDIR}/base_SPI.p1: base_SPI.c nbproject/Makefile-${CND_CONF}.mk
@${MKDIR} ${OBJECTDIR}
@${RM} ${OBJECTDIR}/base_SPI.p1.d
${MP_CC} --pass1 $(MP_EXTRA_CC_PRE) --chip=$(MP_PROCESSOR_OPTION) -Q -G --asmlist --double=24 --float=24 --emi=wordwrite --opt=default,+asm,-asmfile,+speed,-space,-debug,9 --addrqual=ignore --mode=free -P -N255 --warn=0 --summary=default,-psect,-class,+mem,-hex,-file --runtime=default,+clear,+init,-keep,-no_startup,-download,+config,+clib,+plib "--errformat=%%f:%%l: error: %%s" "--warnformat=%%f:%%l: warning: %%s" "--msgformat=%%f:%%l: advisory: %%s" -o${OBJECTDIR}/base_SPI.p1 base_SPI.c
${MP_CC} --pass1 $(MP_EXTRA_CC_PRE) --chip=$(MP_PROCESSOR_OPTION) -Q -G --asmlist --double=24 --float=24 --emi=wordwrite --opt=default,+asm,-asmfile,+speed,-space,-debug,9 --addrqual=ignore --mode=free -P -N255 --warn=0 --summary=default,-psect,-class,+mem,-hex,-file --output=default,-inhx032 --runtime=default,+clear,+init,-keep,-no_startup,-download,+config,+clib,+plib "--errformat=%%f:%%l: error: %%s" "--warnformat=%%f:%%l: warning: %%s" "--msgformat=%%f:%%l: advisory: %%s" -o${OBJECTDIR}/base_SPI.p1 base_SPI.c
@-${MV} ${OBJECTDIR}/base_SPI.d ${OBJECTDIR}/base_SPI.p1.d
@${FIXDEPS} ${OBJECTDIR}/base_SPI.p1.d $(SILENT) -rsi ${MP_CC_DIR}../
237,7 → 237,7
${OBJECTDIR}/display_led_HT16K33.p1: display_led_HT16K33.c nbproject/Makefile-${CND_CONF}.mk
@${MKDIR} ${OBJECTDIR}
@${RM} ${OBJECTDIR}/display_led_HT16K33.p1.d
${MP_CC} --pass1 $(MP_EXTRA_CC_PRE) --chip=$(MP_PROCESSOR_OPTION) -Q -G --asmlist --double=24 --float=24 --emi=wordwrite --opt=default,+asm,-asmfile,+speed,-space,-debug,9 --addrqual=ignore --mode=free -P -N255 --warn=0 --summary=default,-psect,-class,+mem,-hex,-file --runtime=default,+clear,+init,-keep,-no_startup,-download,+config,+clib,+plib "--errformat=%%f:%%l: error: %%s" "--warnformat=%%f:%%l: warning: %%s" "--msgformat=%%f:%%l: advisory: %%s" -o${OBJECTDIR}/display_led_HT16K33.p1 display_led_HT16K33.c
${MP_CC} --pass1 $(MP_EXTRA_CC_PRE) --chip=$(MP_PROCESSOR_OPTION) -Q -G --asmlist --double=24 --float=24 --emi=wordwrite --opt=default,+asm,-asmfile,+speed,-space,-debug,9 --addrqual=ignore --mode=free -P -N255 --warn=0 --summary=default,-psect,-class,+mem,-hex,-file --output=default,-inhx032 --runtime=default,+clear,+init,-keep,-no_startup,-download,+config,+clib,+plib "--errformat=%%f:%%l: error: %%s" "--warnformat=%%f:%%l: warning: %%s" "--msgformat=%%f:%%l: advisory: %%s" -o${OBJECTDIR}/display_led_HT16K33.p1 display_led_HT16K33.c
@-${MV} ${OBJECTDIR}/display_led_HT16K33.d ${OBJECTDIR}/display_led_HT16K33.p1.d
@${FIXDEPS} ${OBJECTDIR}/display_led_HT16K33.p1.d $(SILENT) -rsi ${MP_CC_DIR}../
244,7 → 244,7
${OBJECTDIR}/sensor_nfc_PN532.p1: sensor_nfc_PN532.c nbproject/Makefile-${CND_CONF}.mk
@${MKDIR} ${OBJECTDIR}
@${RM} ${OBJECTDIR}/sensor_nfc_PN532.p1.d
${MP_CC} --pass1 $(MP_EXTRA_CC_PRE) --chip=$(MP_PROCESSOR_OPTION) -Q -G --asmlist --double=24 --float=24 --emi=wordwrite --opt=default,+asm,-asmfile,+speed,-space,-debug,9 --addrqual=ignore --mode=free -P -N255 --warn=0 --summary=default,-psect,-class,+mem,-hex,-file --runtime=default,+clear,+init,-keep,-no_startup,-download,+config,+clib,+plib "--errformat=%%f:%%l: error: %%s" "--warnformat=%%f:%%l: warning: %%s" "--msgformat=%%f:%%l: advisory: %%s" -o${OBJECTDIR}/sensor_nfc_PN532.p1 sensor_nfc_PN532.c
${MP_CC} --pass1 $(MP_EXTRA_CC_PRE) --chip=$(MP_PROCESSOR_OPTION) -Q -G --asmlist --double=24 --float=24 --emi=wordwrite --opt=default,+asm,-asmfile,+speed,-space,-debug,9 --addrqual=ignore --mode=free -P -N255 --warn=0 --summary=default,-psect,-class,+mem,-hex,-file --output=default,-inhx032 --runtime=default,+clear,+init,-keep,-no_startup,-download,+config,+clib,+plib "--errformat=%%f:%%l: error: %%s" "--warnformat=%%f:%%l: warning: %%s" "--msgformat=%%f:%%l: advisory: %%s" -o${OBJECTDIR}/sensor_nfc_PN532.p1 sensor_nfc_PN532.c
@-${MV} ${OBJECTDIR}/sensor_nfc_PN532.d ${OBJECTDIR}/sensor_nfc_PN532.p1.d
@${FIXDEPS} ${OBJECTDIR}/sensor_nfc_PN532.p1.d $(SILENT) -rsi ${MP_CC_DIR}../
251,7 → 251,7
${OBJECTDIR}/base_TIMERS.p1: base_TIMERS.c nbproject/Makefile-${CND_CONF}.mk
@${MKDIR} ${OBJECTDIR}
@${RM} ${OBJECTDIR}/base_TIMERS.p1.d
${MP_CC} --pass1 $(MP_EXTRA_CC_PRE) --chip=$(MP_PROCESSOR_OPTION) -Q -G --asmlist --double=24 --float=24 --emi=wordwrite --opt=default,+asm,-asmfile,+speed,-space,-debug,9 --addrqual=ignore --mode=free -P -N255 --warn=0 --summary=default,-psect,-class,+mem,-hex,-file --runtime=default,+clear,+init,-keep,-no_startup,-download,+config,+clib,+plib "--errformat=%%f:%%l: error: %%s" "--warnformat=%%f:%%l: warning: %%s" "--msgformat=%%f:%%l: advisory: %%s" -o${OBJECTDIR}/base_TIMERS.p1 base_TIMERS.c
${MP_CC} --pass1 $(MP_EXTRA_CC_PRE) --chip=$(MP_PROCESSOR_OPTION) -Q -G --asmlist --double=24 --float=24 --emi=wordwrite --opt=default,+asm,-asmfile,+speed,-space,-debug,9 --addrqual=ignore --mode=free -P -N255 --warn=0 --summary=default,-psect,-class,+mem,-hex,-file --output=default,-inhx032 --runtime=default,+clear,+init,-keep,-no_startup,-download,+config,+clib,+plib "--errformat=%%f:%%l: error: %%s" "--warnformat=%%f:%%l: warning: %%s" "--msgformat=%%f:%%l: advisory: %%s" -o${OBJECTDIR}/base_TIMERS.p1 base_TIMERS.c
@-${MV} ${OBJECTDIR}/base_TIMERS.d ${OBJECTDIR}/base_TIMERS.p1.d
@${FIXDEPS} ${OBJECTDIR}/base_TIMERS.p1.d $(SILENT) -rsi ${MP_CC_DIR}../
258,7 → 258,7
${OBJECTDIR}/comm_xbee.p1: comm_xbee.c nbproject/Makefile-${CND_CONF}.mk
@${MKDIR} ${OBJECTDIR}
@${RM} ${OBJECTDIR}/comm_xbee.p1.d
${MP_CC} --pass1 $(MP_EXTRA_CC_PRE) --chip=$(MP_PROCESSOR_OPTION) -Q -G --asmlist --double=24 --float=24 --emi=wordwrite --opt=default,+asm,-asmfile,+speed,-space,-debug,9 --addrqual=ignore --mode=free -P -N255 --warn=0 --summary=default,-psect,-class,+mem,-hex,-file --runtime=default,+clear,+init,-keep,-no_startup,-download,+config,+clib,+plib "--errformat=%%f:%%l: error: %%s" "--warnformat=%%f:%%l: warning: %%s" "--msgformat=%%f:%%l: advisory: %%s" -o${OBJECTDIR}/comm_xbee.p1 comm_xbee.c
${MP_CC} --pass1 $(MP_EXTRA_CC_PRE) --chip=$(MP_PROCESSOR_OPTION) -Q -G --asmlist --double=24 --float=24 --emi=wordwrite --opt=default,+asm,-asmfile,+speed,-space,-debug,9 --addrqual=ignore --mode=free -P -N255 --warn=0 --summary=default,-psect,-class,+mem,-hex,-file --output=default,-inhx032 --runtime=default,+clear,+init,-keep,-no_startup,-download,+config,+clib,+plib "--errformat=%%f:%%l: error: %%s" "--warnformat=%%f:%%l: warning: %%s" "--msgformat=%%f:%%l: advisory: %%s" -o${OBJECTDIR}/comm_xbee.p1 comm_xbee.c
@-${MV} ${OBJECTDIR}/comm_xbee.d ${OBJECTDIR}/comm_xbee.p1.d
@${FIXDEPS} ${OBJECTDIR}/comm_xbee.p1.d $(SILENT) -rsi ${MP_CC_DIR}../
265,7 → 265,7
${OBJECTDIR}/base_ADC.p1: base_ADC.c nbproject/Makefile-${CND_CONF}.mk
@${MKDIR} ${OBJECTDIR}
@${RM} ${OBJECTDIR}/base_ADC.p1.d
${MP_CC} --pass1 $(MP_EXTRA_CC_PRE) --chip=$(MP_PROCESSOR_OPTION) -Q -G --asmlist --double=24 --float=24 --emi=wordwrite --opt=default,+asm,-asmfile,+speed,-space,-debug,9 --addrqual=ignore --mode=free -P -N255 --warn=0 --summary=default,-psect,-class,+mem,-hex,-file --runtime=default,+clear,+init,-keep,-no_startup,-download,+config,+clib,+plib "--errformat=%%f:%%l: error: %%s" "--warnformat=%%f:%%l: warning: %%s" "--msgformat=%%f:%%l: advisory: %%s" -o${OBJECTDIR}/base_ADC.p1 base_ADC.c
${MP_CC} --pass1 $(MP_EXTRA_CC_PRE) --chip=$(MP_PROCESSOR_OPTION) -Q -G --asmlist --double=24 --float=24 --emi=wordwrite --opt=default,+asm,-asmfile,+speed,-space,-debug,9 --addrqual=ignore --mode=free -P -N255 --warn=0 --summary=default,-psect,-class,+mem,-hex,-file --output=default,-inhx032 --runtime=default,+clear,+init,-keep,-no_startup,-download,+config,+clib,+plib "--errformat=%%f:%%l: error: %%s" "--warnformat=%%f:%%l: warning: %%s" "--msgformat=%%f:%%l: advisory: %%s" -o${OBJECTDIR}/base_ADC.p1 base_ADC.c
@-${MV} ${OBJECTDIR}/base_ADC.d ${OBJECTDIR}/base_ADC.p1.d
@${FIXDEPS} ${OBJECTDIR}/base_ADC.p1.d $(SILENT) -rsi ${MP_CC_DIR}../
272,7 → 272,7
${OBJECTDIR}/base_INTERRUPTS.p1: base_INTERRUPTS.c nbproject/Makefile-${CND_CONF}.mk
@${MKDIR} ${OBJECTDIR}
@${RM} ${OBJECTDIR}/base_INTERRUPTS.p1.d
${MP_CC} --pass1 $(MP_EXTRA_CC_PRE) --chip=$(MP_PROCESSOR_OPTION) -Q -G --asmlist --double=24 --float=24 --emi=wordwrite --opt=default,+asm,-asmfile,+speed,-space,-debug,9 --addrqual=ignore --mode=free -P -N255 --warn=0 --summary=default,-psect,-class,+mem,-hex,-file --runtime=default,+clear,+init,-keep,-no_startup,-download,+config,+clib,+plib "--errformat=%%f:%%l: error: %%s" "--warnformat=%%f:%%l: warning: %%s" "--msgformat=%%f:%%l: advisory: %%s" -o${OBJECTDIR}/base_INTERRUPTS.p1 base_INTERRUPTS.c
${MP_CC} --pass1 $(MP_EXTRA_CC_PRE) --chip=$(MP_PROCESSOR_OPTION) -Q -G --asmlist --double=24 --float=24 --emi=wordwrite --opt=default,+asm,-asmfile,+speed,-space,-debug,9 --addrqual=ignore --mode=free -P -N255 --warn=0 --summary=default,-psect,-class,+mem,-hex,-file --output=default,-inhx032 --runtime=default,+clear,+init,-keep,-no_startup,-download,+config,+clib,+plib "--errformat=%%f:%%l: error: %%s" "--warnformat=%%f:%%l: warning: %%s" "--msgformat=%%f:%%l: advisory: %%s" -o${OBJECTDIR}/base_INTERRUPTS.p1 base_INTERRUPTS.c
@-${MV} ${OBJECTDIR}/base_INTERRUPTS.d ${OBJECTDIR}/base_INTERRUPTS.p1.d
@${FIXDEPS} ${OBJECTDIR}/base_INTERRUPTS.p1.d $(SILENT) -rsi ${MP_CC_DIR}../
279,7 → 279,7
${OBJECTDIR}/display_oled_NHD-0216KZW-AB5.p1: display_oled_NHD-0216KZW-AB5.c nbproject/Makefile-${CND_CONF}.mk
@${MKDIR} ${OBJECTDIR}
@${RM} ${OBJECTDIR}/display_oled_NHD-0216KZW-AB5.p1.d
${MP_CC} --pass1 $(MP_EXTRA_CC_PRE) --chip=$(MP_PROCESSOR_OPTION) -Q -G --asmlist --double=24 --float=24 --emi=wordwrite --opt=default,+asm,-asmfile,+speed,-space,-debug,9 --addrqual=ignore --mode=free -P -N255 --warn=0 --summary=default,-psect,-class,+mem,-hex,-file --runtime=default,+clear,+init,-keep,-no_startup,-download,+config,+clib,+plib "--errformat=%%f:%%l: error: %%s" "--warnformat=%%f:%%l: warning: %%s" "--msgformat=%%f:%%l: advisory: %%s" -o${OBJECTDIR}/display_oled_NHD-0216KZW-AB5.p1 display_oled_NHD-0216KZW-AB5.c
${MP_CC} --pass1 $(MP_EXTRA_CC_PRE) --chip=$(MP_PROCESSOR_OPTION) -Q -G --asmlist --double=24 --float=24 --emi=wordwrite --opt=default,+asm,-asmfile,+speed,-space,-debug,9 --addrqual=ignore --mode=free -P -N255 --warn=0 --summary=default,-psect,-class,+mem,-hex,-file --output=default,-inhx032 --runtime=default,+clear,+init,-keep,-no_startup,-download,+config,+clib,+plib "--errformat=%%f:%%l: error: %%s" "--warnformat=%%f:%%l: warning: %%s" "--msgformat=%%f:%%l: advisory: %%s" -o${OBJECTDIR}/display_oled_NHD-0216KZW-AB5.p1 display_oled_NHD-0216KZW-AB5.c
@-${MV} ${OBJECTDIR}/display_oled_NHD-0216KZW-AB5.d ${OBJECTDIR}/display_oled_NHD-0216KZW-AB5.p1.d
@${FIXDEPS} ${OBJECTDIR}/display_oled_NHD-0216KZW-AB5.p1.d $(SILENT) -rsi ${MP_CC_DIR}../
286,7 → 286,7
${OBJECTDIR}/display_oled_ssd1306.p1: display_oled_ssd1306.c nbproject/Makefile-${CND_CONF}.mk
@${MKDIR} ${OBJECTDIR}
@${RM} ${OBJECTDIR}/display_oled_ssd1306.p1.d
${MP_CC} --pass1 $(MP_EXTRA_CC_PRE) --chip=$(MP_PROCESSOR_OPTION) -Q -G --asmlist --double=24 --float=24 --emi=wordwrite --opt=default,+asm,-asmfile,+speed,-space,-debug,9 --addrqual=ignore --mode=free -P -N255 --warn=0 --summary=default,-psect,-class,+mem,-hex,-file --runtime=default,+clear,+init,-keep,-no_startup,-download,+config,+clib,+plib "--errformat=%%f:%%l: error: %%s" "--warnformat=%%f:%%l: warning: %%s" "--msgformat=%%f:%%l: advisory: %%s" -o${OBJECTDIR}/display_oled_ssd1306.p1 display_oled_ssd1306.c
${MP_CC} --pass1 $(MP_EXTRA_CC_PRE) --chip=$(MP_PROCESSOR_OPTION) -Q -G --asmlist --double=24 --float=24 --emi=wordwrite --opt=default,+asm,-asmfile,+speed,-space,-debug,9 --addrqual=ignore --mode=free -P -N255 --warn=0 --summary=default,-psect,-class,+mem,-hex,-file --output=default,-inhx032 --runtime=default,+clear,+init,-keep,-no_startup,-download,+config,+clib,+plib "--errformat=%%f:%%l: error: %%s" "--warnformat=%%f:%%l: warning: %%s" "--msgformat=%%f:%%l: advisory: %%s" -o${OBJECTDIR}/display_oled_ssd1306.p1 display_oled_ssd1306.c
@-${MV} ${OBJECTDIR}/display_oled_ssd1306.d ${OBJECTDIR}/display_oled_ssd1306.p1.d
@${FIXDEPS} ${OBJECTDIR}/display_oled_ssd1306.p1.d $(SILENT) -rsi ${MP_CC_DIR}../
293,7 → 293,7
${OBJECTDIR}/display_oled_ssd1331.p1: display_oled_ssd1331.c nbproject/Makefile-${CND_CONF}.mk
@${MKDIR} ${OBJECTDIR}
@${RM} ${OBJECTDIR}/display_oled_ssd1331.p1.d
${MP_CC} --pass1 $(MP_EXTRA_CC_PRE) --chip=$(MP_PROCESSOR_OPTION) -Q -G --asmlist --double=24 --float=24 --emi=wordwrite --opt=default,+asm,-asmfile,+speed,-space,-debug,9 --addrqual=ignore --mode=free -P -N255 --warn=0 --summary=default,-psect,-class,+mem,-hex,-file --runtime=default,+clear,+init,-keep,-no_startup,-download,+config,+clib,+plib "--errformat=%%f:%%l: error: %%s" "--warnformat=%%f:%%l: warning: %%s" "--msgformat=%%f:%%l: advisory: %%s" -o${OBJECTDIR}/display_oled_ssd1331.p1 display_oled_ssd1331.c
${MP_CC} --pass1 $(MP_EXTRA_CC_PRE) --chip=$(MP_PROCESSOR_OPTION) -Q -G --asmlist --double=24 --float=24 --emi=wordwrite --opt=default,+asm,-asmfile,+speed,-space,-debug,9 --addrqual=ignore --mode=free -P -N255 --warn=0 --summary=default,-psect,-class,+mem,-hex,-file --output=default,-inhx032 --runtime=default,+clear,+init,-keep,-no_startup,-download,+config,+clib,+plib "--errformat=%%f:%%l: error: %%s" "--warnformat=%%f:%%l: warning: %%s" "--msgformat=%%f:%%l: advisory: %%s" -o${OBJECTDIR}/display_oled_ssd1331.p1 display_oled_ssd1331.c
@-${MV} ${OBJECTDIR}/display_oled_ssd1331.d ${OBJECTDIR}/display_oled_ssd1331.p1.d
@${FIXDEPS} ${OBJECTDIR}/display_oled_ssd1331.p1.d $(SILENT) -rsi ${MP_CC_DIR}../
300,7 → 300,7
${OBJECTDIR}/glcdfont.p1: glcdfont.c nbproject/Makefile-${CND_CONF}.mk
@${MKDIR} ${OBJECTDIR}
@${RM} ${OBJECTDIR}/glcdfont.p1.d
${MP_CC} --pass1 $(MP_EXTRA_CC_PRE) --chip=$(MP_PROCESSOR_OPTION) -Q -G --asmlist --double=24 --float=24 --emi=wordwrite --opt=default,+asm,-asmfile,+speed,-space,-debug,9 --addrqual=ignore --mode=free -P -N255 --warn=0 --summary=default,-psect,-class,+mem,-hex,-file --runtime=default,+clear,+init,-keep,-no_startup,-download,+config,+clib,+plib "--errformat=%%f:%%l: error: %%s" "--warnformat=%%f:%%l: warning: %%s" "--msgformat=%%f:%%l: advisory: %%s" -o${OBJECTDIR}/glcdfont.p1 glcdfont.c
${MP_CC} --pass1 $(MP_EXTRA_CC_PRE) --chip=$(MP_PROCESSOR_OPTION) -Q -G --asmlist --double=24 --float=24 --emi=wordwrite --opt=default,+asm,-asmfile,+speed,-space,-debug,9 --addrqual=ignore --mode=free -P -N255 --warn=0 --summary=default,-psect,-class,+mem,-hex,-file --output=default,-inhx032 --runtime=default,+clear,+init,-keep,-no_startup,-download,+config,+clib,+plib "--errformat=%%f:%%l: error: %%s" "--warnformat=%%f:%%l: warning: %%s" "--msgformat=%%f:%%l: advisory: %%s" -o${OBJECTDIR}/glcdfont.p1 glcdfont.c
@-${MV} ${OBJECTDIR}/glcdfont.d ${OBJECTDIR}/glcdfont.p1.d
@${FIXDEPS} ${OBJECTDIR}/glcdfont.p1.d $(SILENT) -rsi ${MP_CC_DIR}../
307,7 → 307,7
${OBJECTDIR}/sensor_lux_TSL2561.p1: sensor_lux_TSL2561.c nbproject/Makefile-${CND_CONF}.mk
@${MKDIR} ${OBJECTDIR}
@${RM} ${OBJECTDIR}/sensor_lux_TSL2561.p1.d
${MP_CC} --pass1 $(MP_EXTRA_CC_PRE) --chip=$(MP_PROCESSOR_OPTION) -Q -G --asmlist --double=24 --float=24 --emi=wordwrite --opt=default,+asm,-asmfile,+speed,-space,-debug,9 --addrqual=ignore --mode=free -P -N255 --warn=0 --summary=default,-psect,-class,+mem,-hex,-file --runtime=default,+clear,+init,-keep,-no_startup,-download,+config,+clib,+plib "--errformat=%%f:%%l: error: %%s" "--warnformat=%%f:%%l: warning: %%s" "--msgformat=%%f:%%l: advisory: %%s" -o${OBJECTDIR}/sensor_lux_TSL2561.p1 sensor_lux_TSL2561.c
${MP_CC} --pass1 $(MP_EXTRA_CC_PRE) --chip=$(MP_PROCESSOR_OPTION) -Q -G --asmlist --double=24 --float=24 --emi=wordwrite --opt=default,+asm,-asmfile,+speed,-space,-debug,9 --addrqual=ignore --mode=free -P -N255 --warn=0 --summary=default,-psect,-class,+mem,-hex,-file --output=default,-inhx032 --runtime=default,+clear,+init,-keep,-no_startup,-download,+config,+clib,+plib "--errformat=%%f:%%l: error: %%s" "--warnformat=%%f:%%l: warning: %%s" "--msgformat=%%f:%%l: advisory: %%s" -o${OBJECTDIR}/sensor_lux_TSL2561.p1 sensor_lux_TSL2561.c
@-${MV} ${OBJECTDIR}/sensor_lux_TSL2561.d ${OBJECTDIR}/sensor_lux_TSL2561.p1.d
@${FIXDEPS} ${OBJECTDIR}/sensor_lux_TSL2561.p1.d $(SILENT) -rsi ${MP_CC_DIR}../
314,7 → 314,7
${OBJECTDIR}/sensor_temp_BMP085.p1: sensor_temp_BMP085.c nbproject/Makefile-${CND_CONF}.mk
@${MKDIR} ${OBJECTDIR}
@${RM} ${OBJECTDIR}/sensor_temp_BMP085.p1.d
${MP_CC} --pass1 $(MP_EXTRA_CC_PRE) --chip=$(MP_PROCESSOR_OPTION) -Q -G --asmlist --double=24 --float=24 --emi=wordwrite --opt=default,+asm,-asmfile,+speed,-space,-debug,9 --addrqual=ignore --mode=free -P -N255 --warn=0 --summary=default,-psect,-class,+mem,-hex,-file --runtime=default,+clear,+init,-keep,-no_startup,-download,+config,+clib,+plib "--errformat=%%f:%%l: error: %%s" "--warnformat=%%f:%%l: warning: %%s" "--msgformat=%%f:%%l: advisory: %%s" -o${OBJECTDIR}/sensor_temp_BMP085.p1 sensor_temp_BMP085.c
${MP_CC} --pass1 $(MP_EXTRA_CC_PRE) --chip=$(MP_PROCESSOR_OPTION) -Q -G --asmlist --double=24 --float=24 --emi=wordwrite --opt=default,+asm,-asmfile,+speed,-space,-debug,9 --addrqual=ignore --mode=free -P -N255 --warn=0 --summary=default,-psect,-class,+mem,-hex,-file --output=default,-inhx032 --runtime=default,+clear,+init,-keep,-no_startup,-download,+config,+clib,+plib "--errformat=%%f:%%l: error: %%s" "--warnformat=%%f:%%l: warning: %%s" "--msgformat=%%f:%%l: advisory: %%s" -o${OBJECTDIR}/sensor_temp_BMP085.p1 sensor_temp_BMP085.c
@-${MV} ${OBJECTDIR}/sensor_temp_BMP085.d ${OBJECTDIR}/sensor_temp_BMP085.p1.d
@${FIXDEPS} ${OBJECTDIR}/sensor_temp_BMP085.p1.d $(SILENT) -rsi ${MP_CC_DIR}../
321,7 → 321,7
${OBJECTDIR}/sensor_gyro_L3G.p1: sensor_gyro_L3G.c nbproject/Makefile-${CND_CONF}.mk
@${MKDIR} ${OBJECTDIR}
@${RM} ${OBJECTDIR}/sensor_gyro_L3G.p1.d
${MP_CC} --pass1 $(MP_EXTRA_CC_PRE) --chip=$(MP_PROCESSOR_OPTION) -Q -G --asmlist --double=24 --float=24 --emi=wordwrite --opt=default,+asm,-asmfile,+speed,-space,-debug,9 --addrqual=ignore --mode=free -P -N255 --warn=0 --summary=default,-psect,-class,+mem,-hex,-file --runtime=default,+clear,+init,-keep,-no_startup,-download,+config,+clib,+plib "--errformat=%%f:%%l: error: %%s" "--warnformat=%%f:%%l: warning: %%s" "--msgformat=%%f:%%l: advisory: %%s" -o${OBJECTDIR}/sensor_gyro_L3G.p1 sensor_gyro_L3G.c
${MP_CC} --pass1 $(MP_EXTRA_CC_PRE) --chip=$(MP_PROCESSOR_OPTION) -Q -G --asmlist --double=24 --float=24 --emi=wordwrite --opt=default,+asm,-asmfile,+speed,-space,-debug,9 --addrqual=ignore --mode=free -P -N255 --warn=0 --summary=default,-psect,-class,+mem,-hex,-file --output=default,-inhx032 --runtime=default,+clear,+init,-keep,-no_startup,-download,+config,+clib,+plib "--errformat=%%f:%%l: error: %%s" "--warnformat=%%f:%%l: warning: %%s" "--msgformat=%%f:%%l: advisory: %%s" -o${OBJECTDIR}/sensor_gyro_L3G.p1 sensor_gyro_L3G.c
@-${MV} ${OBJECTDIR}/sensor_gyro_L3G.d ${OBJECTDIR}/sensor_gyro_L3G.p1.d
@${FIXDEPS} ${OBJECTDIR}/sensor_gyro_L3G.p1.d $(SILENT) -rsi ${MP_CC_DIR}../
328,7 → 328,7
${OBJECTDIR}/sensor_accel_LSM303.p1: sensor_accel_LSM303.c nbproject/Makefile-${CND_CONF}.mk
@${MKDIR} ${OBJECTDIR}
@${RM} ${OBJECTDIR}/sensor_accel_LSM303.p1.d
${MP_CC} --pass1 $(MP_EXTRA_CC_PRE) --chip=$(MP_PROCESSOR_OPTION) -Q -G --asmlist --double=24 --float=24 --emi=wordwrite --opt=default,+asm,-asmfile,+speed,-space,-debug,9 --addrqual=ignore --mode=free -P -N255 --warn=0 --summary=default,-psect,-class,+mem,-hex,-file --runtime=default,+clear,+init,-keep,-no_startup,-download,+config,+clib,+plib "--errformat=%%f:%%l: error: %%s" "--warnformat=%%f:%%l: warning: %%s" "--msgformat=%%f:%%l: advisory: %%s" -o${OBJECTDIR}/sensor_accel_LSM303.p1 sensor_accel_LSM303.c
${MP_CC} --pass1 $(MP_EXTRA_CC_PRE) --chip=$(MP_PROCESSOR_OPTION) -Q -G --asmlist --double=24 --float=24 --emi=wordwrite --opt=default,+asm,-asmfile,+speed,-space,-debug,9 --addrqual=ignore --mode=free -P -N255 --warn=0 --summary=default,-psect,-class,+mem,-hex,-file --output=default,-inhx032 --runtime=default,+clear,+init,-keep,-no_startup,-download,+config,+clib,+plib "--errformat=%%f:%%l: error: %%s" "--warnformat=%%f:%%l: warning: %%s" "--msgformat=%%f:%%l: advisory: %%s" -o${OBJECTDIR}/sensor_accel_LSM303.p1 sensor_accel_LSM303.c
@-${MV} ${OBJECTDIR}/sensor_accel_LSM303.d ${OBJECTDIR}/sensor_accel_LSM303.p1.d
@${FIXDEPS} ${OBJECTDIR}/sensor_accel_LSM303.p1.d $(SILENT) -rsi ${MP_CC_DIR}../
335,7 → 335,7
${OBJECTDIR}/sensor_rtc_DS3231.p1: sensor_rtc_DS3231.c nbproject/Makefile-${CND_CONF}.mk
@${MKDIR} ${OBJECTDIR}
@${RM} ${OBJECTDIR}/sensor_rtc_DS3231.p1.d
${MP_CC} --pass1 $(MP_EXTRA_CC_PRE) --chip=$(MP_PROCESSOR_OPTION) -Q -G --asmlist --double=24 --float=24 --emi=wordwrite --opt=default,+asm,-asmfile,+speed,-space,-debug,9 --addrqual=ignore --mode=free -P -N255 --warn=0 --summary=default,-psect,-class,+mem,-hex,-file --runtime=default,+clear,+init,-keep,-no_startup,-download,+config,+clib,+plib "--errformat=%%f:%%l: error: %%s" "--warnformat=%%f:%%l: warning: %%s" "--msgformat=%%f:%%l: advisory: %%s" -o${OBJECTDIR}/sensor_rtc_DS3231.p1 sensor_rtc_DS3231.c
${MP_CC} --pass1 $(MP_EXTRA_CC_PRE) --chip=$(MP_PROCESSOR_OPTION) -Q -G --asmlist --double=24 --float=24 --emi=wordwrite --opt=default,+asm,-asmfile,+speed,-space,-debug,9 --addrqual=ignore --mode=free -P -N255 --warn=0 --summary=default,-psect,-class,+mem,-hex,-file --output=default,-inhx032 --runtime=default,+clear,+init,-keep,-no_startup,-download,+config,+clib,+plib "--errformat=%%f:%%l: error: %%s" "--warnformat=%%f:%%l: warning: %%s" "--msgformat=%%f:%%l: advisory: %%s" -o${OBJECTDIR}/sensor_rtc_DS3231.p1 sensor_rtc_DS3231.c
@-${MV} ${OBJECTDIR}/sensor_rtc_DS3231.d ${OBJECTDIR}/sensor_rtc_DS3231.p1.d
@${FIXDEPS} ${OBJECTDIR}/sensor_rtc_DS3231.p1.d $(SILENT) -rsi ${MP_CC_DIR}../
352,13 → 352,13
ifeq ($(TYPE_IMAGE), DEBUG_RUN)
dist/${CND_CONF}/${IMAGE_TYPE}/PICX_27J13.${IMAGE_TYPE}.${OUTPUT_SUFFIX}: ${OBJECTFILES} nbproject/Makefile-${CND_CONF}.mk
@${MKDIR} dist/${CND_CONF}/${IMAGE_TYPE}
${MP_CC} $(MP_EXTRA_LD_PRE) --chip=$(MP_PROCESSOR_OPTION) -G --asmlist -mdist/${CND_CONF}/${IMAGE_TYPE}/PICX_27J13.${IMAGE_TYPE}.map -D__DEBUG=1 --debugger=pickit3 --double=24 --float=24 --emi=wordwrite --opt=default,+asm,-asmfile,+speed,-space,-debug,9 --addrqual=ignore --mode=free -P -N255 --warn=0 --summary=default,-psect,-class,+mem,-hex,-file --runtime=default,+clear,+init,-keep,-no_startup,-download,+config,+clib,+plib "--errformat=%%f:%%l: error: %%s" "--warnformat=%%f:%%l: warning: %%s" "--msgformat=%%f:%%l: advisory: %%s" -odist/${CND_CONF}/${IMAGE_TYPE}/PICX_27J13.${IMAGE_TYPE}.${DEBUGGABLE_SUFFIX} ${OBJECTFILES_QUOTED_IF_SPACED}
${MP_CC} $(MP_EXTRA_LD_PRE) --chip=$(MP_PROCESSOR_OPTION) -G --asmlist -mdist/${CND_CONF}/${IMAGE_TYPE}/PICX_27J13.${IMAGE_TYPE}.map -D__DEBUG=1 --debugger=pickit3 --double=24 --float=24 --emi=wordwrite --opt=default,+asm,-asmfile,+speed,-space,-debug,9 --addrqual=ignore --mode=free -P -N255 --warn=0 --summary=default,-psect,-class,+mem,-hex,-file --output=default,-inhx032 --runtime=default,+clear,+init,-keep,-no_startup,-download,+config,+clib,+plib "--errformat=%%f:%%l: error: %%s" "--warnformat=%%f:%%l: warning: %%s" "--msgformat=%%f:%%l: advisory: %%s" -odist/${CND_CONF}/${IMAGE_TYPE}/PICX_27J13.${IMAGE_TYPE}.${DEBUGGABLE_SUFFIX} ${OBJECTFILES_QUOTED_IF_SPACED}
@${RM} dist/${CND_CONF}/${IMAGE_TYPE}/PICX_27J13.${IMAGE_TYPE}.hex
else
dist/${CND_CONF}/${IMAGE_TYPE}/PICX_27J13.${IMAGE_TYPE}.${OUTPUT_SUFFIX}: ${OBJECTFILES} nbproject/Makefile-${CND_CONF}.mk
@${MKDIR} dist/${CND_CONF}/${IMAGE_TYPE}
${MP_CC} $(MP_EXTRA_LD_PRE) --chip=$(MP_PROCESSOR_OPTION) -G --asmlist -mdist/${CND_CONF}/${IMAGE_TYPE}/PICX_27J13.${IMAGE_TYPE}.map --double=24 --float=24 --emi=wordwrite --opt=default,+asm,-asmfile,+speed,-space,-debug,9 --addrqual=ignore --mode=free -P -N255 --warn=0 --summary=default,-psect,-class,+mem,-hex,-file --runtime=default,+clear,+init,-keep,-no_startup,-download,+config,+clib,+plib "--errformat=%%f:%%l: error: %%s" "--warnformat=%%f:%%l: warning: %%s" "--msgformat=%%f:%%l: advisory: %%s" -odist/${CND_CONF}/${IMAGE_TYPE}/PICX_27J13.${IMAGE_TYPE}.${DEBUGGABLE_SUFFIX} ${OBJECTFILES_QUOTED_IF_SPACED}
${MP_CC} $(MP_EXTRA_LD_PRE) --chip=$(MP_PROCESSOR_OPTION) -G --asmlist -mdist/${CND_CONF}/${IMAGE_TYPE}/PICX_27J13.${IMAGE_TYPE}.map --double=24 --float=24 --emi=wordwrite --opt=default,+asm,-asmfile,+speed,-space,-debug,9 --addrqual=ignore --mode=free -P -N255 --warn=0 --summary=default,-psect,-class,+mem,-hex,-file --output=default,-inhx032 --runtime=default,+clear,+init,-keep,-no_startup,-download,+config,+clib,+plib "--errformat=%%f:%%l: error: %%s" "--warnformat=%%f:%%l: warning: %%s" "--msgformat=%%f:%%l: advisory: %%s" -odist/${CND_CONF}/${IMAGE_TYPE}/PICX_27J13.${IMAGE_TYPE}.${DEBUGGABLE_SUFFIX} ${OBJECTFILES_QUOTED_IF_SPACED}
endif
 
/PIC Stuff/PICX_27J13/nbproject/Makefile-genesis.properties
1,8 → 1,8
#
#Sat Jan 05 02:50:26 EST 2013
#Tue Apr 23 02:19:35 EDT 2013
default.languagetoolchain.dir=C\:\\Program Files (x86)\\Microchip\\xc8\\v1.12\\bin
com-microchip-mplab-nbide-embedded-makeproject-MakeProject.md5=d94e033fce233e60ccb9abf3a212a9b7
com-microchip-mplab-nbide-embedded-makeproject-MakeProject.md5=415494acd195d89b2f6d7a36797a5ab4
default.languagetoolchain.version=1.12
host.platform=windows
conf.ids=default
default.com-microchip-mplab-nbide-toolchainXC8-XC8LanguageToolchain.md5=8fc157cf2b8157578b9f80e4bbee68f8
default.com-microchip-mplab-nbide-toolchainXC8-XC8LanguageToolchain.md5=10ef1ca121a2d422272c53829f548789
/PIC Stuff/PICX_27J13/nbproject/configurations.xml
147,6 → 147,34
<property key="program-the-device-with-default-config-words" value="true"/>
</HI-TECH-LINK>
<PICkit3PlatformTool>
<property key="AutoSelectMemRanges" value="auto"/>
<property key="Freeze Peripherals" value="true"/>
<property key="SecureSegment.SegmentProgramming" value="FullChipProgramming"/>
<property key="ToolFirmwareFilePath"
value="Press to browse for a specific firmware version"/>
<property key="ToolFirmwareOption.UseLatestFirmware" value="true"/>
<property key="hwtoolclock.frcindebug" value="false"/>
<property key="memories.aux" value="false"/>
<property key="memories.bootflash" value="false"/>
<property key="memories.configurationmemory" value="false"/>
<property key="memories.eeprom" value="false"/>
<property key="memories.flashdata" value="true"/>
<property key="memories.id" value="false"/>
<property key="memories.programmemory" value="true"/>
<property key="memories.programmemory.end" value="0x1fff7"/>
<property key="memories.programmemory.start" value="0x0"/>
<property key="poweroptions.powerenable" value="true"/>
<property key="programmertogo.imagename" value=""/>
<property key="programoptions.eraseb4program" value="true"/>
<property key="programoptions.pgmspeed" value="2"/>
<property key="programoptions.preserveeeprom" value="false"/>
<property key="programoptions.preserveprogramrange" value="false"/>
<property key="programoptions.preserveprogramrange.end" value="0x1fff7"/>
<property key="programoptions.preserveprogramrange.start" value="0x0"/>
<property key="programoptions.preserveuserid" value="false"/>
<property key="programoptions.usehighvoltageonmclr" value="false"/>
<property key="programoptions.uselvpprogramming" value="false"/>
<property key="voltagevalue" value="3.25"/>
</PICkit3PlatformTool>
<XC8-config-global>
</XC8-config-global>
/PIC Stuff/PICX_27J13/nbproject/private/private.xml
1,4 → 1,7
<?xml version="1.0" encoding="UTF-8"?>
<project-private xmlns="http://www.netbeans.org/ns/project-private/1">
<editor-bookmarks xmlns="http://www.netbeans.org/ns/editor-bookmarks/1"/>
<open-files xmlns="http://www.netbeans.org/ns/projectui-open-files/1">
<file>file:/C:/Users/Kevin/Documents/Code/PICX_27J13/main.c</file>
</open-files>
</project-private>