15,7 → 15,7 |
#pragma config MCLRE = ON // MCLR/VPP pin function is MCLR |
#pragma config WDTE = OFF // WDT disabled |
#pragma config CP = OFF // Program memory code protection is disabled |
#pragma config PWRTE = OFF // PWRT disabled |
#pragma config PWRTE = ON // PWRT enabled |
#pragma config CLKOUTEN = OFF // CLKOUT function is disabled. I/O or oscillator function on the CLKOUT pin |
|
/* Config Register CONFIG2 @ 0x8008 */ |
38,12 → 38,13 |
|
ANSELA = 0x00; // All pins set to digital I/O |
APFCONbits.CCP1SEL = 1; // Switch CCP1 from RA2 to RA5 |
WPUA = 0x00; // Disable weak pull-ups |
|
// Wait for HFINTOSC to be within 0.5% of target 32Mhz |
while (!OSCSTATbits.HFIOFS); |
|
Interrupt_Enable(); |
|
|
I2C1_Init(); |
I2C1_Configure_Master(I2C_1MHZ); |
|
55,8 → 56,8 |
TSL2561_Init(TSL2561_ADDR_FLOAT); |
|
// You can change the gain on the fly, to adapt to brighter/dimmer light situations |
TSL2561_Set_Gain(TSL2561_GAIN_0X); // set no gain (for bright situtations) |
// TSL2561_Set_Gain(TSL2561_GAIN_16X); // set 16x gain (for dim situations) |
// TSL2561_Set_Gain(TSL2561_GAIN_0X); // set no gain (for bright situtations) |
TSL2561_Set_Gain(TSL2561_GAIN_16X); // set 16x gain (for dim situations) |
|
// Changing the integration time gives you a longer time over which to sense light |
// longer timelines are slower, but are good in very low light situtations! |
64,42 → 65,50 |
TSL2561_Set_Timing(TSL2561_INTEGRATIONTIME_101MS); // medium integration time (medium light) |
// TSL2561_Set_Timing(TSL2561_INTEGRATIONTIME_402MS); // longest integration time (dim light) |
|
// uint16_t full, ir, vis; |
uint16_t full; |
uint8_t multiplier, multiplier_2; |
|
// time.sec = 0; |
// time.min = 16; |
// time.hour = 7; |
// time.h_mil = 0; |
// time.h_am_pm = 1; |
// |
// DS3231_Set_Time(&time); |
|
while(1) { |
// full = TSL2561_Get_Luminosity(0); |
// ir = TSL2561_Get_Luminosity(1); |
// vis = full - ir; |
// |
// ~37200 seems to be the max value at 16X gain, 101ms period |
full = TSL2561_Get_Luminosity(0); |
multiplier = (full / 3100) + 1; // 12 levels (1-12) |
multiplier_2 = (multiplier / 7) + 1; // 2 levels (1-2) |
|
// NeoPixel_Clear(); |
// for (uint8_t i = 0; i < (vis >> 11); i++) { |
// NeoPixel_Set(i, 0x10, 0x00, 0x00); |
// for (uint8_t i = 0; i < multiplier; i++) { |
// NeoPixel_Set(i, 0x10, 0x00, 0x00, 1); |
// } |
// NeoPixel_Write_All(); |
// |
// __delay_ms(100); |
|
|
DS3231_Get_Time(&time); |
NeoPixel_Clear(); |
|
// Draw markers |
NeoPixel_Set(0, 0x10, 0x00, 0x00); |
NeoPixel_Set(5, 0x08, 0x02, 0x00); |
NeoPixel_Set(10, 0x08, 0x08, 0x00); |
NeoPixel_Set(15, 0x00, 0x10, 0x00); |
NeoPixel_Set(20, 0x00, 0x00, 0x10); |
NeoPixel_Set(25, 0x08, 0x00, 0x08); |
NeoPixel_Set(30, 0x10, 0x00, 0x00); |
NeoPixel_Set(35, 0x08, 0x02, 0x00); |
NeoPixel_Set(40, 0x08, 0x08, 0x00); |
NeoPixel_Set(45, 0x00, 0x10, 0x00); |
NeoPixel_Set(50, 0x00, 0x00, 0x10); |
NeoPixel_Set(55, 0x08, 0x00, 0x08); |
NeoPixel_Set(00, RED, multiplier_2); |
NeoPixel_Set(30, RED, multiplier_2); |
NeoPixel_Set(05, ORANGE, multiplier_2); |
NeoPixel_Set(35, ORANGE, multiplier_2); |
NeoPixel_Set(10, YELLOW, multiplier_2); |
NeoPixel_Set(40, YELLOW, multiplier_2); |
NeoPixel_Set(15, GREEN, multiplier_2); |
NeoPixel_Set(45, GREEN, multiplier_2); |
NeoPixel_Set(20, BLUE, multiplier_2); |
NeoPixel_Set(50, BLUE, multiplier_2); |
NeoPixel_Set(25, PURPLE, multiplier_2); |
NeoPixel_Set(55, PURPLE, multiplier_2); |
|
// Draw time |
NeoPixel_Or((time.hour * 5) % 60, BLUE); |
NeoPixel_Or(time.min, GREEN); |
NeoPixel_Or(time.sec, RED); |
NeoPixel_Or((time.hour * 5) % 60, BLUE, multiplier + 4); |
NeoPixel_Or(time.min, GREEN, multiplier + 4); |
NeoPixel_Or(time.sec, RED, multiplier + 4); |
NeoPixel_Write_All(); |
} |
} |