| 152 |
Kevin |
1 |
#include <xc.h>
|
|
|
2 |
#include <delays.h>
|
|
|
3 |
#include <stdio.h>
|
| 155 |
Kevin |
4 |
#include <string.h>
|
| 152 |
Kevin |
5 |
#include "defines.h"
|
| 155 |
Kevin |
6 |
#include "interrupts.h"
|
| 152 |
Kevin |
7 |
#include "uart.h"
|
| 155 |
Kevin |
8 |
#include "i2c.h"
|
|
|
9 |
#include "spi.h"
|
|
|
10 |
#include "nfc_PN532.h"
|
|
|
11 |
#include "led_HT16K33.h"
|
|
|
12 |
#include "oled_ssd1306.h"
|
|
|
13 |
#include "oled_ssd1331.h"
|
|
|
14 |
#include "timers.h"
|
|
|
15 |
#include "lux_TSL2561.h"
|
|
|
16 |
#include "oled_NHD-0216KZW-AB5.h"
|
|
|
17 |
#include "adc.h"
|
|
|
18 |
#include "temp_BMP085.h"
|
| 152 |
Kevin |
19 |
|
|
|
20 |
// <editor-fold defaultstate="collapsed" desc="Configuration Bits">
|
|
|
21 |
/* --------------------------- Configuration Bits --------------------------- */
|
|
|
22 |
/* CONFIG1L @ 0x1FFF8 */
|
|
|
23 |
#pragma config CFGPLLEN = ON // Enable PLL on startup
|
|
|
24 |
#pragma config PLLDIV = 3 // Set PPL prescaler to 3 (to get 4MHz)
|
|
|
25 |
#pragma config WDTEN = OFF // Turn off watchdog timer
|
|
|
26 |
#pragma config STVREN = OFF // Stack overflow/underflow reset disabled
|
|
|
27 |
#pragma config XINST = OFF // Turn off extended instruction set
|
|
|
28 |
|
|
|
29 |
/* CONFIG1H @ 0x1FFF9 */
|
|
|
30 |
#pragma config CP0 = OFF // Program memory is not code-protected
|
|
|
31 |
|
|
|
32 |
/* CONFIG2L @ 0x1FFFA */
|
|
|
33 |
#pragma config CLKOEC = OFF // CLKO output disabled on RA6 pin
|
|
|
34 |
#pragma config SOSCSEL = LOW // Low Power T1OSC/SOSC circuit selected
|
|
|
35 |
#pragma config IESO = ON // Internal external oscillator switch over disabled
|
|
|
36 |
#pragma config OSC = HSPLL // Use external oscillator (101)
|
|
|
37 |
#pragma config FCMEN = OFF // Fail-safe clock monitor disabled
|
|
|
38 |
|
|
|
39 |
/* CONFIG2H @ 0x1FFFB */
|
|
|
40 |
#pragma config WDTPS = 1 // Watchdog postscaler of 1:1
|
|
|
41 |
|
|
|
42 |
/* CONFIG3L @ 0x1FFFC */
|
|
|
43 |
#pragma config RTCOSC = T1OSCREF // RTCC uses T1OSC/T1CKI
|
|
|
44 |
#pragma config DSBOREN = ON // Deep sleep BOR enabled
|
|
|
45 |
#pragma config DSWDTPS = M2 // Deep sleep watchdog postscaler of 1:2 (36m)
|
|
|
46 |
#pragma config DSWDTEN = OFF // Deep sleep watchdog timer disabled
|
|
|
47 |
#pragma config DSWDTOSC = INTOSCREF // DSWDT clock select uses INTRC
|
|
|
48 |
|
|
|
49 |
/* CONFIG3H @ 0x1FFFD */
|
|
|
50 |
#pragma config PLLSEL = PLL96 // Use 96MHz PLL 4MHz -> 96MHz / 2 = 48MHz
|
|
|
51 |
#pragma config ADCSEL = BIT12 // 12-bit ADC
|
|
|
52 |
#pragma config MSSP7B_EN = MSK7 // 7-bit address masking mode
|
|
|
53 |
#pragma config IOL1WAY = OFF // IOLOCK bit can be set and cleared as needed
|
|
|
54 |
|
|
|
55 |
/* CONFIG4L @ 0x1FFFE */
|
|
|
56 |
#pragma config WPCFG = ON // Configuration words page protected
|
|
|
57 |
|
|
|
58 |
/* CONFIG4H @ 0x1FFFF */
|
|
|
59 |
#pragma config WPEND = PAGE_WPFP // Pages WPFP<6:0> through Configuration Words erase/write protected
|
|
|
60 |
#pragma config WPDIS = OFF // WPFP<6:0>/WPEND region ignored
|
|
|
61 |
/* -------------------------------------------------------------------------- */
|
|
|
62 |
// </editor-fold>
|
|
|
63 |
|
|
|
64 |
#if defined(_TEST_UART)
|
|
|
65 |
int main() {
|
|
|
66 |
char buffer[100];
|
| 155 |
Kevin |
67 |
|
|
|
68 |
// Set all ports as digial I/O
|
|
|
69 |
ANCON0 = 0xFF;
|
|
|
70 |
ANCON1 = 0x1F;
|
|
|
71 |
|
|
|
72 |
UART_DATA uart_data;
|
|
|
73 |
UART1_Init(&uart_data); // Initialize the UART handler code
|
|
|
74 |
|
|
|
75 |
Interrupt_Init(); // Initialize the interrupt priorities
|
|
|
76 |
Interrupt_Enable(); // Enable high-priority interrupts and low-priority interrupts
|
|
|
77 |
|
|
|
78 |
char output[] = "\r\nBegin Program\r\n";
|
|
|
79 |
DBG_PRINT_MAIN(output, strlen(output));
|
|
|
80 |
|
|
|
81 |
while (1) {
|
|
|
82 |
char length = UART1_Read_Buffer((char *) buffer);
|
|
|
83 |
if (length != 0) {
|
|
|
84 |
UART1_WriteS(buffer, length);
|
|
|
85 |
}
|
|
|
86 |
|
|
|
87 |
Delay10KTCYx(255);
|
|
|
88 |
Delay10KTCYx(255);
|
|
|
89 |
}
|
|
|
90 |
}
|
|
|
91 |
#elif defined(_TEST_I2C_MASTER)
|
|
|
92 |
void main(void) {
|
|
|
93 |
char length = 0;
|
|
|
94 |
char result = 0;
|
|
|
95 |
char buffer[100];
|
|
|
96 |
char output[64];
|
|
|
97 |
|
|
|
98 |
// Set all ports as digial I/O
|
|
|
99 |
ANCON0 = 0xFF;
|
|
|
100 |
ANCON1 = 0x1F;
|
|
|
101 |
|
|
|
102 |
UART_DATA uart_data;
|
|
|
103 |
UART1_Init(&uart_data); // Initialize the UART handler code
|
|
|
104 |
I2C_DATA i2c_data;
|
|
|
105 |
I2C_Init(&i2c_data); // Initialize the I2C handler code
|
|
|
106 |
|
|
|
107 |
I2C_Configure_Master(I2C_100KHZ);
|
|
|
108 |
|
|
|
109 |
Interrupt_Init(); // Initialize the interrupt priorities
|
|
|
110 |
Interrupt_Enable(); // Enable high-priority interrupts and low-priority interrupts
|
|
|
111 |
|
|
|
112 |
sprintf(output, "\r\nBegin Program\r\n");
|
|
|
113 |
DBG_PRINT_MAIN(output, strlen(output));
|
|
|
114 |
|
|
|
115 |
while (1) {
|
|
|
116 |
buffer[0] = 0x8;
|
|
|
117 |
|
|
|
118 |
I2C_Master_Send(0x24, 1, buffer);
|
|
|
119 |
do {
|
|
|
120 |
result = I2C_Get_Status();
|
|
|
121 |
} while (!result);
|
|
|
122 |
sprintf(output, "S: %X ", result);
|
|
|
123 |
DBG_PRINT_MAIN(output, strlen(output));
|
|
|
124 |
|
|
|
125 |
I2C_Master_Recv(0x24, 2);
|
|
|
126 |
do {
|
|
|
127 |
result = I2C_Get_Status();
|
|
|
128 |
} while (!result);
|
|
|
129 |
sprintf(output, "S: %X ", result);
|
|
|
130 |
DBG_PRINT_MAIN(output, strlen(output));
|
|
|
131 |
length = I2C_Read_Buffer(buffer);
|
|
|
132 |
sprintf(output, "L: %d D: ", length);
|
|
|
133 |
DBG_PRINT_MAIN(output, strlen(output));
|
|
|
134 |
for (char i = 0; i < length; i++) {
|
|
|
135 |
sprintf(output, "%c ", buffer[i]);
|
|
|
136 |
DBG_PRINT_MAIN(output, strlen(output));
|
|
|
137 |
}
|
|
|
138 |
sprintf(output, "\r\n");
|
|
|
139 |
DBG_PRINT_MAIN(output, strlen(output));
|
|
|
140 |
|
|
|
141 |
I2C_Master_Restart(0x30, 0xBB, 2);
|
|
|
142 |
result = I2C_Get_Status();
|
|
|
143 |
while (!result) {
|
|
|
144 |
result = I2C_Get_Status();
|
|
|
145 |
}
|
|
|
146 |
sprintf(output, "S: %X ", result);
|
|
|
147 |
DBG_PRINT_MAIN(output, strlen(output));
|
|
|
148 |
length = I2C_Read_Buffer(buffer);
|
|
|
149 |
sprintf(output, "L: %d D: ", length);
|
|
|
150 |
DBG_PRINT_MAIN(output, strlen(output));
|
|
|
151 |
for (char i = 0; i < length; i++) {
|
|
|
152 |
sprintf(output, "%c ", buffer[i]);
|
|
|
153 |
DBG_PRINT_MAIN(output, strlen(output));
|
|
|
154 |
}
|
|
|
155 |
sprintf(output, "\r\n");
|
|
|
156 |
DBG_PRINT_MAIN(output, strlen(output));
|
|
|
157 |
|
|
|
158 |
Delay10KTCYx(255);
|
|
|
159 |
Delay10KTCYx(255);
|
|
|
160 |
}
|
|
|
161 |
}
|
|
|
162 |
#elif defined(_TEST_I2C_SLAVE)
|
|
|
163 |
void main(void) {
|
|
|
164 |
char length = 0;
|
|
|
165 |
char result = 0;
|
|
|
166 |
char buffer[100];
|
|
|
167 |
char output[64];
|
|
|
168 |
|
|
|
169 |
// Set all ports as digial I/O
|
|
|
170 |
ANCON0 = 0xFF;
|
|
|
171 |
ANCON1 = 0x1F;
|
|
|
172 |
|
|
|
173 |
UART_DATA uart_data;
|
|
|
174 |
UART1_Init(&uart_data); // Initialize the UART handler code
|
|
|
175 |
I2C_DATA i2c_data;
|
|
|
176 |
I2C_Init(&i2c_data); // Initialize the I2C handler code
|
|
|
177 |
|
|
|
178 |
I2C_Configure_Slave(0x24);
|
|
|
179 |
|
|
|
180 |
Interrupt_Init(); // Initialize the interrupt priorities
|
|
|
181 |
Interrupt_Enable(); // Enable high-priority interrupts and low-priority interrupts
|
|
|
182 |
|
|
|
183 |
sprintf(output, "\r\nBegin Program\r\n");
|
|
|
184 |
DBG_PRINT_MAIN(output, strlen(output));
|
|
|
185 |
|
|
|
186 |
while (1) {
|
|
|
187 |
|
|
|
188 |
result = I2C_Get_Status();
|
|
|
189 |
while (!result) {
|
|
|
190 |
result = I2C_Get_Status();
|
|
|
191 |
}
|
|
|
192 |
sprintf(output, "S: %X ", result);
|
|
|
193 |
DBG_PRINT_MAIN(output, strlen(output));
|
|
|
194 |
length = I2C_Read_Buffer(buffer);
|
|
|
195 |
sprintf(output, "L: %d D: ", length);
|
|
|
196 |
DBG_PRINT_MAIN(output, strlen(output));
|
|
|
197 |
for (char i = 0; i < length; i++) {
|
|
|
198 |
sprintf(output, "%X ", buffer[i]);
|
|
|
199 |
DBG_PRINT_MAIN(output, strlen(output));
|
|
|
200 |
}
|
|
|
201 |
sprintf(output, "\r\n");
|
|
|
202 |
DBG_PRINT_MAIN(output, strlen(output));
|
|
|
203 |
|
|
|
204 |
Delay10KTCYx(255);
|
|
|
205 |
Delay10KTCYx(255);
|
|
|
206 |
}
|
|
|
207 |
}
|
|
|
208 |
#elif defined(_TEST_SPI)
|
|
|
209 |
void main(void) {
|
|
|
210 |
char length = 0;
|
|
|
211 |
char result = 0;
|
|
|
212 |
char buffer[100];
|
|
|
213 |
char output[64];
|
|
|
214 |
char test[8] = "ASDF123";
|
|
|
215 |
|
|
|
216 |
// Set all ports as digial I/O
|
|
|
217 |
ANCON0 = 0xFF;
|
|
|
218 |
ANCON1 = 0x1F;
|
|
|
219 |
|
|
|
220 |
UART_DATA uart_data;
|
|
|
221 |
UART1_Init(&uart_data); // Initialize the UART handler code
|
|
|
222 |
SPI_DATA spi_data;
|
|
|
223 |
SPI2_Init(&spi_data, SPI2_FOSC_8); // Initialize the SPI module
|
|
|
224 |
|
|
|
225 |
Interrupt_Init(); // Initialize the interrupt priorities
|
|
|
226 |
Interrupt_Enable(); // Enable high-priority interrupts and low-priority interrupts
|
|
|
227 |
|
|
|
228 |
sprintf(output, "\r\nBegin Program\r\n");
|
|
|
229 |
DBG_PRINT_MAIN(output, strlen(output));
|
|
|
230 |
|
|
|
231 |
while (1) {
|
|
|
232 |
|
|
|
233 |
SPI2_Write(test, 7);
|
|
|
234 |
while (result != 7) {
|
|
|
235 |
length = SPI2_Read_Buffer(buffer);
|
|
|
236 |
if (length) {
|
|
|
237 |
result += length;
|
|
|
238 |
}
|
|
|
239 |
}
|
|
|
240 |
result = 0;
|
|
|
241 |
|
|
|
242 |
for (char i = 0; i < result; i++) {
|
|
|
243 |
sprintf(output, "%X ", buffer[i]);
|
|
|
244 |
DBG_PRINT_MAIN(output, strlen(output));
|
|
|
245 |
}
|
|
|
246 |
sprintf(output, "\r\n");
|
|
|
247 |
DBG_PRINT_MAIN(output, strlen(output));
|
|
|
248 |
|
|
|
249 |
Delay10KTCYx(255);
|
|
|
250 |
Delay10KTCYx(255);
|
|
|
251 |
}
|
|
|
252 |
}
|
|
|
253 |
#elif defined(_TEST_NFC)
|
|
|
254 |
void main(void) {
|
|
|
255 |
char length = 0;
|
|
|
256 |
char output[64];
|
|
|
257 |
|
|
|
258 |
// NFC stuff
|
|
|
259 |
NFC_FIRMWARE_VERSION version;
|
|
|
260 |
NFC_TargetDataMiFare cardData[2];
|
|
|
261 |
NFC_TargetDataMiFare cardData_prev[2];
|
|
|
262 |
|
|
|
263 |
// Set all ports as digial I/O
|
|
|
264 |
ANCON0 = 0xFF;
|
|
|
265 |
ANCON1 = 0x1F;
|
|
|
266 |
|
|
|
267 |
UART_DATA uart_data;
|
|
|
268 |
UART1_Init(&uart_data); // Initialize the UART handler code
|
|
|
269 |
I2C_DATA i2c_data;
|
|
|
270 |
I2C_Init(&i2c_data); // Initialize the I2C handler code
|
|
|
271 |
NFC_DATA nfc_data;
|
|
|
272 |
NFC_Init(&nfc_data); // Initialize the NFC chip (uses I2C)
|
|
|
273 |
|
|
|
274 |
I2C_Configure_Master(I2C_400KHZ);
|
|
|
275 |
|
|
|
276 |
Interrupt_Init(); // Initialize the interrupt priorities
|
|
|
277 |
Interrupt_Enable(); // Enable high-priority interrupts and low-priority interrupts
|
|
|
278 |
|
|
|
279 |
sprintf(output, "\r\nBegin Program\r\n");
|
|
|
280 |
DBG_PRINT_MAIN(output, strlen(output));
|
|
|
281 |
|
|
|
282 |
version = NFC_Get_Firmware_Version();
|
|
|
283 |
while (!version.IC) {
|
|
|
284 |
sprintf(output, "Waiting for NFC board..\r\n");
|
|
|
285 |
DBG_PRINT_MAIN(output, strlen(output));
|
|
|
286 |
Delay10KTCYx(3);
|
|
|
287 |
version = NFC_Get_Firmware_Version();
|
|
|
288 |
}
|
|
|
289 |
sprintf(output, "Found chip PN5%X\r\n", version.IC);
|
|
|
290 |
DBG_PRINT_MAIN(output, strlen(output));
|
|
|
291 |
sprintf(output, "Firmware ver. %d.%d\r\n", version.Ver, version.Rev);
|
|
|
292 |
DBG_PRINT_MAIN(output, strlen(output));
|
|
|
293 |
NFC_SAMConfig();
|
|
|
294 |
|
|
|
295 |
memset(cardData, 0, 24);
|
|
|
296 |
|
|
|
297 |
while (1) {
|
|
|
298 |
|
|
|
299 |
// // This query will hang until the NFC chip replies (card detected)
|
|
|
300 |
// length = NFC_readPassiveTargetID(cardData);
|
|
|
301 |
// if (length) {
|
|
|
302 |
// DBG_PRINT_MAIN("Cards Found: %u\r\n", length);
|
|
|
303 |
// DBG_PRINT_MAIN("UID Length: %d bytes\r\n", cardData[0].NFCID_LEN);
|
|
|
304 |
// DBG_PRINT_MAIN("UID: ");
|
|
|
305 |
// for (i = 0; i < cardData[0].NFCID_LEN; i++) {
|
|
|
306 |
// DBG_PRINT_MAIN("%02X ", cardData[0].NFCID[i]);
|
|
|
307 |
// }
|
|
|
308 |
// DBG_PRINT_MAIN("\r\n");
|
|
|
309 |
// if (length == 2) {
|
|
|
310 |
// DBG_PRINT_MAIN("UID Length: %d bytes\r\n", cardData[1].NFCID_LEN);
|
|
|
311 |
// DBG_PRINT_MAIN("UID: ");
|
|
|
312 |
// for (i = 0; i < cardData[1].NFCID_LEN; i++) {
|
|
|
313 |
// DBG_PRINT_MAIN("%02X ", cardData[1].NFCID[i]);
|
|
|
314 |
// }
|
|
|
315 |
// DBG_PRINT_MAIN("\r\n");
|
|
|
316 |
// }
|
|
|
317 |
// }
|
|
|
318 |
|
|
|
319 |
// // This query will hang until the NFC chip replies (card detected)
|
|
|
320 |
// length = NFC_readPassiveTargetID(cardData);
|
|
|
321 |
// if (length) {
|
|
|
322 |
// DBG_PRINT_MAIN("Cards Found: %u\r\n", length);
|
|
|
323 |
// DBG_PRINT_MAIN("UID Length: %d bytes\r\n", cardData[0].NFCID_LEN);
|
|
|
324 |
// DBG_PRINT_MAIN("UID: ");
|
|
|
325 |
// for (i = 0; i < cardData[0].NFCID_LEN; i++) {
|
|
|
326 |
// DBG_PRINT_MAIN("%02X ", cardData[0].NFCID[i]);
|
|
|
327 |
// }
|
|
|
328 |
// DBG_PRINT_MAIN("\r\n");
|
|
|
329 |
// if (length == 2) {
|
|
|
330 |
// DBG_PRINT_MAIN("UID Length: %d bytes\r\n", cardData[1].NFCID_LEN);
|
|
|
331 |
// DBG_PRINT_MAIN("UID: ");
|
|
|
332 |
// for (i = 0; i < cardData[1].NFCID_LEN; i++) {
|
|
|
333 |
// DBG_PRINT_MAIN("%02X ", cardData[1].NFCID[i]);
|
|
|
334 |
// }
|
|
|
335 |
// DBG_PRINT_MAIN("\r\n");
|
|
|
336 |
// }
|
|
|
337 |
// }
|
|
|
338 |
|
|
|
339 |
// This query will not wait for a detection before responding
|
|
|
340 |
length = NFC_Poll_Targets(1, 1, cardData);
|
|
|
341 |
if (!length) {
|
|
|
342 |
memset(cardData_prev, 0, 24);
|
|
|
343 |
} else if (length == 1) {
|
|
|
344 |
if (memcmp(&cardData[0].NFCID, &cardData_prev[0].NFCID, cardData[0].NFCID_LEN) == 0) {
|
|
|
345 |
// Do nothing
|
|
|
346 |
} else if (memcmp(&cardData[0].NFCID, &cardData_prev[1].NFCID, cardData[0].NFCID_LEN) == 0) {
|
|
|
347 |
memcpy((char *) &cardData_prev[0], (const char *) &cardData[0], 12);
|
|
|
348 |
} else {
|
|
|
349 |
sprintf(output, "UID: ");
|
|
|
350 |
DBG_PRINT_MAIN(output, strlen(output));
|
|
|
351 |
for (char i = 0; i < cardData[0].NFCID_LEN; i++) {
|
|
|
352 |
sprintf(output, "%02X ", cardData[0].NFCID[i]);
|
|
|
353 |
DBG_PRINT_MAIN(output, strlen(output));
|
|
|
354 |
}
|
|
|
355 |
sprintf(output, "\r\n");
|
|
|
356 |
DBG_PRINT_MAIN(output, strlen(output));
|
|
|
357 |
memcpy((char *) &cardData_prev[0], (const char *) &cardData[0], 12);
|
|
|
358 |
}
|
|
|
359 |
memset(&cardData_prev[1], 0, 12);
|
|
|
360 |
} else if (length == 2) {
|
|
|
361 |
if (memcmp(&cardData[0].NFCID, &cardData_prev[0].NFCID, cardData[0].NFCID_LEN) == 0 &&
|
|
|
362 |
memcmp(&cardData[1].NFCID, &cardData_prev[1].NFCID, cardData[1].NFCID_LEN) == 0) {
|
|
|
363 |
// Do nothing
|
|
|
364 |
} else if (memcmp(&cardData[0].NFCID, &cardData_prev[1].NFCID, cardData[0].NFCID_LEN) == 0 &&
|
|
|
365 |
memcmp(&cardData[1].NFCID, &cardData_prev[0].NFCID, cardData[1].NFCID_LEN) == 0) {
|
|
|
366 |
memcpy((char *) &cardData_prev[0], (const char *) &cardData[0], 12);
|
|
|
367 |
memcpy((char *) &cardData_prev[1], (const char *) &cardData[1], 12);
|
|
|
368 |
} else if (memcmp(&cardData[0].NFCID, &cardData_prev[0].NFCID, cardData[0].NFCID_LEN) == 0) {
|
|
|
369 |
// First card matched
|
|
|
370 |
sprintf(output, "UID2: ");
|
|
|
371 |
DBG_PRINT_MAIN(output, strlen(output));
|
|
|
372 |
for (char i = 0; i < cardData[1].NFCID_LEN; i++) {
|
|
|
373 |
sprintf(output, "%02X ", cardData[1].NFCID[i]);
|
|
|
374 |
DBG_PRINT_MAIN(output, strlen(output));
|
|
|
375 |
}
|
|
|
376 |
sprintf(output, "\r\n");
|
|
|
377 |
DBG_PRINT_MAIN(output, strlen(output));
|
|
|
378 |
memcpy(&cardData_prev[1], (const char *) &cardData[1], 12);
|
|
|
379 |
} else if (memcmp(&cardData[1].NFCID, &cardData_prev[1].NFCID, cardData[1].NFCID_LEN) == 0) {
|
|
|
380 |
// Second card matched
|
|
|
381 |
sprintf(output, "UID1: ");
|
|
|
382 |
DBG_PRINT_MAIN(output, strlen(output));
|
|
|
383 |
for (char i = 0; i < cardData[0].NFCID_LEN; i++) {
|
|
|
384 |
sprintf(output, "%02X ", cardData[0].NFCID[i]);
|
|
|
385 |
DBG_PRINT_MAIN(output, strlen(output));
|
|
|
386 |
}
|
|
|
387 |
sprintf(output, "\r\n");
|
|
|
388 |
DBG_PRINT_MAIN(output, strlen(output));
|
|
|
389 |
memcpy((char *) &cardData_prev[0], (const char *) &cardData[0], 12);
|
|
|
390 |
} else {
|
|
|
391 |
// No match
|
|
|
392 |
sprintf(output, "UID1: ");
|
|
|
393 |
DBG_PRINT_MAIN(output, strlen(output));
|
|
|
394 |
for (char i = 0; i < cardData[0].NFCID_LEN; i++) {
|
|
|
395 |
sprintf(output, "%02X ", cardData[0].NFCID[i]);
|
|
|
396 |
DBG_PRINT_MAIN(output, strlen(output));
|
|
|
397 |
}
|
|
|
398 |
sprintf(output, "\r\n");
|
|
|
399 |
DBG_PRINT_MAIN(output, strlen(output));
|
|
|
400 |
memcpy((char *) &cardData_prev[0], (const char *) &cardData[0], 12);
|
|
|
401 |
sprintf(output, "UID2: ");
|
|
|
402 |
DBG_PRINT_MAIN(output, strlen(output));
|
|
|
403 |
for (char i = 0; i < cardData[1].NFCID_LEN; i++) {
|
|
|
404 |
sprintf(output, "%02X ", cardData[1].NFCID[i]);
|
|
|
405 |
DBG_PRINT_MAIN(output, strlen(output));
|
|
|
406 |
}
|
|
|
407 |
sprintf(output, "\r\n");
|
|
|
408 |
DBG_PRINT_MAIN(output, strlen(output));
|
|
|
409 |
memcpy((char *) &cardData_prev[1], (const char *) &cardData[1], 12);
|
|
|
410 |
}
|
|
|
411 |
}
|
|
|
412 |
}
|
|
|
413 |
}
|
|
|
414 |
#elif defined(_TEST_LED_BACKPACK)
|
|
|
415 |
void main(void) {
|
|
|
416 |
unsigned int counter = 0;
|
|
|
417 |
char output[64];
|
|
|
418 |
|
|
|
419 |
// Set all ports as digial I/O
|
|
|
420 |
ANCON0 = 0xFF;
|
|
|
421 |
ANCON1 = 0x1F;
|
|
|
422 |
|
|
|
423 |
UART_DATA uart_data;
|
|
|
424 |
UART1_Init(&uart_data); // Initialize the UART handler code
|
|
|
425 |
I2C_DATA i2c_data;
|
|
|
426 |
I2C_Init(&i2c_data); // Initialize the I2C handler code
|
|
|
427 |
LED_DATA led_data;
|
|
|
428 |
LED_Init(&led_data); // Initialize the LED backpack (uses I2C);
|
|
|
429 |
|
|
|
430 |
I2C_Configure_Master(I2C_400KHZ);
|
|
|
431 |
|
|
|
432 |
Interrupt_Init(); // Initialize the interrupt priorities
|
|
|
433 |
Interrupt_Enable(); // Enable high-priority interrupts and low-priority interrupts
|
|
|
434 |
|
|
|
435 |
sprintf(output, "\r\nBegin Program\r\n");
|
|
|
436 |
DBG_PRINT_MAIN(output, strlen(output));
|
|
|
437 |
|
|
|
438 |
LED_Start();
|
|
|
439 |
LED_Write_Digit_Num(0, 1, 1);
|
|
|
440 |
LED_Write_Digit_Num(1, 2, 0);
|
|
|
441 |
LED_Write_Digit_Num(2, 3, 0);
|
|
|
442 |
LED_Write_Digit_Num(3, 4, 0);
|
|
|
443 |
LED_Write_Display();
|
|
|
444 |
for (char i = 0; i < 15; i++) {
|
|
|
445 |
LED_Set_Brightness(15 - i);
|
|
|
446 |
Delay10KTCYx(100);
|
|
|
447 |
}
|
|
|
448 |
for (char i = 0; i < 15; i++) {
|
|
|
449 |
LED_Set_Brightness(i);
|
|
|
450 |
Delay10KTCYx(100);
|
|
|
451 |
}
|
|
|
452 |
LED_Blink_Rate(HT16K33_BLINK_OFF);
|
|
|
453 |
|
|
|
454 |
while (1) {
|
|
|
455 |
LED_Write_Num(counter);
|
|
|
456 |
counter++;
|
|
|
457 |
if (counter > 9999)
|
|
|
458 |
counter = 0;
|
|
|
459 |
|
|
|
460 |
// Delay10KTCYx(255);
|
|
|
461 |
}
|
|
|
462 |
}
|
|
|
463 |
#elif defined(_TEST_SSD1306_OLED)
|
|
|
464 |
void main(void) {
|
|
|
465 |
char output[64];
|
|
|
466 |
|
|
|
467 |
// Set all ports as digial I/O
|
|
|
468 |
ANCON0 = 0xFF;
|
|
|
469 |
ANCON1 = 0x1F;
|
|
|
470 |
|
|
|
471 |
UART_DATA uart_data;
|
|
|
472 |
UART1_Init(&uart_data); // Initialize the UART handler code
|
|
|
473 |
SPI_DATA spi_data;
|
|
|
474 |
SPI2_Init(&spi_data, SPI2_FOSC_4); // Initialize the SPI module
|
|
|
475 |
SSD1306_DATA ssd1306_data;
|
|
|
476 |
SSD1306_Init(&ssd1306_data); // Initialize the OLED code
|
|
|
477 |
|
|
|
478 |
Interrupt_Init(); // Initialize the interrupt priorities
|
|
|
479 |
Interrupt_Enable(); // Enable high-priority interrupts and low-priority interrupts
|
|
|
480 |
|
|
|
481 |
sprintf(output, "\r\nBegin Program\r\n");
|
|
|
482 |
DBG_PRINT_MAIN(output, strlen(output));
|
|
|
483 |
|
|
|
484 |
SSD1306_Begin(SSD1306_SWITCHCAPVCC);
|
|
|
485 |
|
|
|
486 |
SSD1306_Display(); // Show splashscreen
|
|
|
487 |
|
|
|
488 |
while (1) {
|
|
|
489 |
Delay10KTCYx(255);
|
|
|
490 |
Delay10KTCYx(255);
|
|
|
491 |
SSD1306_Clear_Display();
|
|
|
492 |
SSD1306_Test_DrawLine();
|
|
|
493 |
SSD1306_Display();
|
|
|
494 |
|
|
|
495 |
Delay10KTCYx(255);
|
|
|
496 |
Delay10KTCYx(255);
|
|
|
497 |
SSD1306_Clear_Display();
|
|
|
498 |
SSD1306_Test_DrawRect();
|
|
|
499 |
SSD1306_Display();
|
|
|
500 |
|
|
|
501 |
Delay10KTCYx(255);
|
|
|
502 |
Delay10KTCYx(255);
|
|
|
503 |
SSD1306_Clear_Display();
|
|
|
504 |
SSD1306_Test_FillRect();
|
|
|
505 |
SSD1306_Display();
|
|
|
506 |
|
|
|
507 |
Delay10KTCYx(255);
|
|
|
508 |
Delay10KTCYx(255);
|
|
|
509 |
SSD1306_Clear_Display();
|
|
|
510 |
SSD1306_Test_DrawCircle();
|
|
|
511 |
SSD1306_Display();
|
|
|
512 |
|
|
|
513 |
Delay10KTCYx(255);
|
|
|
514 |
Delay10KTCYx(255);
|
|
|
515 |
SSD1306_Clear_Display();
|
|
|
516 |
SSD1306_Fill_Circle(SSD1306_LCDWIDTH / 2, SSD1306_LCDHEIGHT / 2, 10, SSD1306_WHITE);
|
|
|
517 |
SSD1306_Display();
|
|
|
518 |
|
|
|
519 |
Delay10KTCYx(255);
|
|
|
520 |
Delay10KTCYx(255);
|
|
|
521 |
SSD1306_Clear_Display();
|
|
|
522 |
SSD1306_Test_DrawRoundRect();
|
|
|
523 |
SSD1306_Display();
|
|
|
524 |
|
|
|
525 |
Delay10KTCYx(255);
|
|
|
526 |
Delay10KTCYx(255);
|
|
|
527 |
SSD1306_Clear_Display();
|
|
|
528 |
SSD1306_Test_FillRoundRect();
|
|
|
529 |
SSD1306_Display();
|
|
|
530 |
|
|
|
531 |
Delay10KTCYx(255);
|
|
|
532 |
Delay10KTCYx(255);
|
|
|
533 |
SSD1306_Clear_Display();
|
|
|
534 |
SSD1306_Test_DrawTriangle();
|
|
|
535 |
SSD1306_Display();
|
|
|
536 |
|
|
|
537 |
Delay10KTCYx(255);
|
|
|
538 |
Delay10KTCYx(255);
|
|
|
539 |
SSD1306_Clear_Display();
|
|
|
540 |
SSD1306_Test_FillTriangle();
|
|
|
541 |
SSD1306_Display();
|
|
|
542 |
|
|
|
543 |
Delay10KTCYx(255);
|
|
|
544 |
Delay10KTCYx(255);
|
|
|
545 |
SSD1306_Clear_Display();
|
|
|
546 |
SSD1306_Test_DrawChar();
|
|
|
547 |
SSD1306_Display();
|
|
|
548 |
|
|
|
549 |
Delay10KTCYx(255);
|
|
|
550 |
Delay10KTCYx(255);
|
|
|
551 |
SSD1306_Clear_Display();
|
|
|
552 |
SSD1306_Set_Text_Size(1);
|
|
|
553 |
SSD1306_Set_Text_Color(SSD1306_WHITE);
|
|
|
554 |
SSD1306_Set_Cursor(0, 0);
|
|
|
555 |
sprintf(output, "Hello World!\n");
|
|
|
556 |
SSD1306_Write_String(output, strlen(output));
|
|
|
557 |
// SSD1306_Set_Text_Color_BG(BLACK, WHITE);
|
|
|
558 |
unsigned int i = 65535;
|
|
|
559 |
sprintf(output, "%u %d\n", i, i);
|
|
|
560 |
SSD1306_Write_String(output, strlen(output));
|
|
|
561 |
// SSD1306_Set_Text_Size(2);
|
|
|
562 |
// SSD1306_Set_Text_Color(WHITE);
|
|
|
563 |
unsigned long l = 0xDEADBEEF;
|
|
|
564 |
sprintf(output, "0x%lX", (long) l);
|
|
|
565 |
SSD1306_Write_String(output, strlen(output));
|
|
|
566 |
SSD1306_Display();
|
|
|
567 |
|
|
|
568 |
// SSD1306_Clear_Display();
|
|
|
569 |
// SSD1306_Set_Rotation(0);
|
|
|
570 |
// SSD1306_Set_Text_Size(1);
|
|
|
571 |
// SSD1306_Set_Text_Color(SSD1306_WHITE);
|
|
|
572 |
// SSD1306_Set_Cursor(0, 0);
|
|
|
573 |
// SSD1306_Write_String("%u", i);
|
|
|
574 |
// i++;
|
|
|
575 |
// SSD1306_Display();
|
|
|
576 |
|
|
|
577 |
}
|
|
|
578 |
}
|
|
|
579 |
#elif defined(_TEST_SSD1331_OLED)
|
|
|
580 |
void main(void) {
|
|
|
581 |
char output[128];
|
|
|
582 |
|
|
|
583 |
// Set all ports as digial I/O
|
|
|
584 |
ANCON0 = 0xFF;
|
|
|
585 |
ANCON1 = 0x1F;
|
|
|
586 |
|
|
|
587 |
UART_DATA uart_data;
|
|
|
588 |
UART1_Init(&uart_data); // Initialize the UART handler code
|
|
|
589 |
SPI_DATA spi_data;
|
|
|
590 |
SPI2_Init(&spi_data, SPI2_FOSC_64); // Initialize the SPI module
|
|
|
591 |
SSD1331_DATA ssd1331_data;
|
|
|
592 |
SSD1331_Init(&ssd1331_data); // Initialize the OLED code
|
|
|
593 |
|
|
|
594 |
Interrupt_Init(); // Initialize the interrupt priorities
|
|
|
595 |
Interrupt_Enable(); // Enable high-priority interrupts and low-priority interrupts
|
|
|
596 |
|
|
|
597 |
sprintf(output, "\r\nBegin Program\r\n");
|
|
|
598 |
DBG_PRINT_MAIN(output, strlen(output));
|
|
|
599 |
|
|
|
600 |
SSD1331_Begin();
|
|
|
601 |
|
|
|
602 |
while (1) {
|
|
|
603 |
|
|
|
604 |
Delay10KTCYx(255);
|
|
|
605 |
Delay10KTCYx(255);
|
|
|
606 |
SSD1331_Set_Rotation(0);
|
|
|
607 |
SSD1331_Test_Pattern();
|
|
|
608 |
|
|
|
609 |
Delay10KTCYx(255);
|
|
|
610 |
Delay10KTCYx(255);
|
|
|
611 |
SSD1331_Clear_Display();
|
|
|
612 |
SSD1331_Set_Rotation(0);
|
|
|
613 |
SSD1331_Set_Cursor(0, 0);
|
|
|
614 |
// TODO: Figure out why this isnt working (probably a compiler issue)
|
|
|
615 |
sprintf(output, "Lorem ipsum dolor sit amet, consectetur adipiscing elit. Curabit adipiscing ante sed nibh tincidunt feugiat.");
|
|
|
616 |
DBG_PRINT_MAIN(output, strlen(output));
|
|
|
617 |
|
|
|
618 |
// Delay10KTCYx(255);
|
|
|
619 |
// Delay10KTCYx(255);
|
|
|
620 |
// SSD1331_Clear_Display();
|
|
|
621 |
// SSD1331_Set_Rotation(3);
|
|
|
622 |
// SSD1331_Set_Cursor(0, 0);
|
|
|
623 |
// SSD1331_Write_String("Lorem ipsum dolor sit amet, consectetur adipiscing elit. Curabitur adipiscing ante sed nibh tincidunt feugiat. Maecenas enim massa");
|
|
|
624 |
|
|
|
625 |
Delay10KTCYx(255);
|
|
|
626 |
Delay10KTCYx(255);
|
|
|
627 |
SSD1331_Set_Rotation(0);
|
|
|
628 |
SSD1331_Test_DrawLines(SSD1331_YELLOW);
|
|
|
629 |
|
|
|
630 |
Delay10KTCYx(255);
|
|
|
631 |
Delay10KTCYx(255);
|
|
|
632 |
SSD1331_Set_Rotation(3);
|
|
|
633 |
SSD1331_Test_DrawLines(SSD1331_BLUE);
|
|
|
634 |
|
|
|
635 |
Delay10KTCYx(255);
|
|
|
636 |
Delay10KTCYx(255);
|
|
|
637 |
SSD1331_Set_Rotation(0);
|
|
|
638 |
SSD1331_Test_DrawRect(SSD1331_GREEN);
|
|
|
639 |
|
|
|
640 |
Delay10KTCYx(255);
|
|
|
641 |
Delay10KTCYx(255);
|
|
|
642 |
SSD1331_Set_Rotation(1);
|
|
|
643 |
SSD1331_Test_DrawRect(SSD1331_RED);
|
|
|
644 |
|
|
|
645 |
Delay10KTCYx(255);
|
|
|
646 |
Delay10KTCYx(255);
|
|
|
647 |
SSD1331_Set_Rotation(2);
|
|
|
648 |
SSD1331_Test_DrawRect(SSD1331_BLUE);
|
|
|
649 |
|
|
|
650 |
Delay10KTCYx(255);
|
|
|
651 |
Delay10KTCYx(255);
|
|
|
652 |
SSD1331_Set_Rotation(3);
|
|
|
653 |
SSD1331_Test_DrawRect(SSD1331_YELLOW);
|
|
|
654 |
|
|
|
655 |
Delay10KTCYx(255);
|
|
|
656 |
Delay10KTCYx(255);
|
|
|
657 |
SSD1331_Set_Rotation(0);
|
|
|
658 |
SSD1331_Test_FillRect(SSD1331_YELLOW, SSD1331_MAGENTA);
|
|
|
659 |
|
|
|
660 |
Delay10KTCYx(255);
|
|
|
661 |
Delay10KTCYx(255);
|
|
|
662 |
SSD1331_Set_Rotation(3);
|
|
|
663 |
SSD1331_Test_FillRect(SSD1331_BLUE, SSD1331_GREEN);
|
|
|
664 |
|
|
|
665 |
Delay10KTCYx(255);
|
|
|
666 |
Delay10KTCYx(255);
|
|
|
667 |
SSD1331_Set_Rotation(0);
|
|
|
668 |
SSD1331_Clear_Display();
|
|
|
669 |
SSD1331_Test_FillCircle(10, SSD1331_BLUE);
|
|
|
670 |
SSD1331_Test_DrawCircle(10, SSD1331_WHITE);
|
|
|
671 |
|
|
|
672 |
Delay10KTCYx(255);
|
|
|
673 |
Delay10KTCYx(255);
|
|
|
674 |
SSD1331_Set_Rotation(3);
|
|
|
675 |
SSD1331_Clear_Display();
|
|
|
676 |
SSD1331_Test_FillCircle(10, SSD1331_MAGENTA);
|
|
|
677 |
SSD1331_Test_DrawCircle(10, SSD1331_YELLOW);
|
|
|
678 |
|
|
|
679 |
Delay10KTCYx(255);
|
|
|
680 |
Delay10KTCYx(255);
|
|
|
681 |
SSD1331_Set_Rotation(0);
|
|
|
682 |
SSD1331_Test_DrawTria();
|
|
|
683 |
|
|
|
684 |
Delay10KTCYx(255);
|
|
|
685 |
Delay10KTCYx(255);
|
|
|
686 |
SSD1331_Set_Rotation(3);
|
|
|
687 |
SSD1331_Test_DrawTria();
|
|
|
688 |
|
|
|
689 |
Delay10KTCYx(255);
|
|
|
690 |
Delay10KTCYx(255);
|
|
|
691 |
SSD1331_Set_Rotation(0);
|
|
|
692 |
SSD1331_Test_DrawRoundRect();
|
|
|
693 |
|
|
|
694 |
Delay10KTCYx(255);
|
|
|
695 |
Delay10KTCYx(255);
|
|
|
696 |
SSD1331_Set_Rotation(3);
|
|
|
697 |
SSD1331_Test_DrawRoundRect();
|
|
|
698 |
|
|
|
699 |
// SSD1331_Clear_Display();
|
|
|
700 |
// SSD1331_Set_Rotation(3);
|
|
|
701 |
// SSD1331_Set_Cursor(0,0);
|
|
|
702 |
// SSD1331_Set_Text_Color_BG(SSD1331_WHITE, SSD1331_BLACK);
|
|
|
703 |
// SSD1331_Write_String("%u", i);
|
|
|
704 |
// i++;
|
|
|
705 |
}
|
|
|
706 |
}
|
|
|
707 |
#elif defined(_TEST_TIMER1_RTC)
|
|
|
708 |
void main(void) {
|
|
|
709 |
|
|
|
710 |
// Set all ports as digial I/O except for AN0-AN2 (pins 2-4)
|
|
|
711 |
ANCON0 = 0xF8;
|
|
|
712 |
ANCON1 = 0x1F;
|
|
|
713 |
|
|
|
714 |
Timer1_Init();
|
|
|
715 |
|
|
|
716 |
Interrupt_Init(); // Initialize the interrupt priorities
|
|
|
717 |
Interrupt_Enable(); // Enable high-priority interrupts and low-priority interrupts
|
|
|
718 |
|
|
|
719 |
LED_BLUE_TRIS = 0;
|
|
|
720 |
LED_RED_TRIS = 0;
|
|
|
721 |
|
|
|
722 |
Timer1_Enable();
|
|
|
723 |
|
|
|
724 |
while (1) {
|
|
|
725 |
|
|
|
726 |
}
|
|
|
727 |
}
|
|
|
728 |
#elif defined(_TEST_LUX)
|
|
|
729 |
void main(void) {
|
|
|
730 |
char output[64];
|
|
|
731 |
|
|
|
732 |
// Set all ports as digial I/O except for AN0-AN2 (pins 2-4)
|
|
|
733 |
ANCON0 = 0xF8;
|
|
|
734 |
ANCON1 = 0x1F;
|
|
|
735 |
|
|
|
736 |
UART_DATA uart_data;
|
|
|
737 |
UART1_Init(&uart_data);
|
|
|
738 |
I2C_DATA i2c_data;
|
|
|
739 |
I2C_Init(&i2c_data);
|
|
|
740 |
TSL2561_DATA lux_data;
|
|
|
741 |
LUX_Init(&lux_data, TSL2561_ADDR_FLOAT);
|
|
|
742 |
|
|
|
743 |
I2C_Configure_Master(I2C_100KHZ);
|
|
|
744 |
|
|
|
745 |
Interrupt_Init(); // Initialize the interrupt priorities
|
|
|
746 |
Interrupt_Enable(); // Enable high-priority interrupts and low-priority interrupts
|
|
|
747 |
|
|
|
748 |
LUX_Begin();
|
|
|
749 |
|
|
|
750 |
// You can change the gain on the fly, to adapt to brighter/dimmer light situations
|
|
|
751 |
// LUX_Set_Gain(TSL2561_GAIN_0X); // set no gain (for bright situtations)
|
|
|
752 |
LUX_Set_Gain(TSL2561_GAIN_16X); // set 16x gain (for dim situations)
|
|
|
753 |
|
|
|
754 |
// Changing the integration time gives you a longer time over which to sense light
|
|
|
755 |
// longer timelines are slower, but are good in very low light situtations!
|
|
|
756 |
// LUX_Set_Timing(TSL2561_INTEGRATIONTIME_13MS); // shortest integration time (bright light)
|
|
|
757 |
LUX_Set_Timing(TSL2561_INTEGRATIONTIME_101MS); // medium integration time (medium light)
|
|
|
758 |
// LUX_Set_Timing(TSL2561_INTEGRATIONTIME_402MS); // longest integration time (dim light)
|
|
|
759 |
|
|
|
760 |
sprintf(output, "\r\nBegin Program\r\n");
|
|
|
761 |
DBG_PRINT_MAIN(output, strlen(output));
|
|
|
762 |
|
|
|
763 |
while (1) {
|
|
|
764 |
unsigned long lum = LUX_Get_Full_Luminosity();
|
|
|
765 |
unsigned int ir = lum >> 16;
|
|
|
766 |
unsigned int full = lum & 0xFFFF;
|
|
|
767 |
sprintf(output, "IR: %d\r\n", ir);
|
|
|
768 |
DBG_PRINT_MAIN(output, strlen(output));
|
|
|
769 |
sprintf(output, "Visible: %d\r\n", full - ir);
|
|
|
770 |
DBG_PRINT_MAIN(output, strlen(output));
|
|
|
771 |
sprintf(output, "Full: %d\r\n", full);
|
|
|
772 |
DBG_PRINT_MAIN(output, strlen(output));
|
|
|
773 |
sprintf(output, "Lux: %ld\r\n\r\n", LUX_Calculate_Lux(full, ir));
|
|
|
774 |
DBG_PRINT_MAIN(output, strlen(output));
|
|
|
775 |
|
|
|
776 |
Delay10KTCYx(255);
|
|
|
777 |
Delay10KTCYx(255);
|
|
|
778 |
Delay10KTCYx(255);
|
|
|
779 |
Delay10KTCYx(255);
|
|
|
780 |
}
|
|
|
781 |
}
|
|
|
782 |
#elif defined(_TEST_OLED_CHAR)
|
|
|
783 |
void main(void) {
|
|
|
784 |
char output[64];
|
|
|
785 |
|
|
|
786 |
// Set all ports as digial I/O except for AN0-AN2 (pins 2-4)
|
|
|
787 |
ANCON0 = 0xFF;
|
|
|
788 |
ANCON1 = 0x1F;
|
|
|
789 |
|
|
|
790 |
// UART1_Init();
|
|
|
791 |
OLED_CHAR_DATA oled_data;
|
|
|
792 |
NHD_Init(&oled_data);
|
|
|
793 |
|
|
|
794 |
Interrupt_Init(); // Initialize the interrupt priorities
|
|
|
795 |
Interrupt_Enable(); // Enable high-priority interrupts and low-priority interrupts
|
|
|
796 |
|
|
|
797 |
NHD_Begin(16, 2);
|
|
|
798 |
|
|
|
799 |
sprintf(output, "Lorem ipsum dolor sit amet, consectetur adipisicing elit, sed do");
|
|
|
800 |
NHD_Write_String(output, strlen(output));
|
|
|
801 |
NHD_Set_Cursor(0,1);
|
|
|
802 |
sprintf(output, "eiusmod tempor incididunt ut labore et dolore magna aliqua. Ut e");
|
|
|
803 |
NHD_Write_String(output, strlen(output));
|
|
|
804 |
|
|
|
805 |
while (1) {
|
|
|
806 |
Delay10KTCYx(150);
|
|
|
807 |
NHD_Scroll_Display_Left();
|
|
|
808 |
}
|
|
|
809 |
}
|
|
|
810 |
#elif defined(_TEST_NFC_TO_SSD1306_OLED)
|
|
|
811 |
void main(void) {
|
|
|
812 |
char output[64];
|
|
|
813 |
|
|
|
814 |
// NFC stuff
|
|
|
815 |
NFC_FIRMWARE_VERSION version;
|
|
|
816 |
NFC_TargetDataMiFare cardData[2];
|
|
|
817 |
NFC_TargetDataMiFare cardData_prev[2];
|
|
|
818 |
|
|
|
819 |
// Set all ports as digial I/O except for AN0-AN2 (pins 2-4)
|
|
|
820 |
ANCON0 = 0xF8;
|
|
|
821 |
ANCON1 = 0x1F;
|
|
|
822 |
|
|
|
823 |
UART_DATA uart_data;
|
|
|
824 |
UART1_Init(&uart_data);
|
|
|
825 |
I2C_DATA i2c_data;
|
|
|
826 |
I2C_Init(&i2c_data);
|
|
|
827 |
NFC_DATA nfc_data;
|
|
|
828 |
NFC_Init(&nfc_data);
|
|
|
829 |
SPI_DATA spi_data;
|
|
|
830 |
SPI2_Init(&spi_data, SPI2_FOSC_4);
|
|
|
831 |
SSD1306_DATA ssd1306_data;
|
|
|
832 |
SSD1306_Init(&ssd1306_data);
|
|
|
833 |
|
|
|
834 |
I2C_Configure_Master(I2C_400KHZ);
|
|
|
835 |
|
|
|
836 |
Interrupt_Init(); // Initialize the interrupt priorities
|
|
|
837 |
Interrupt_Enable(); // Enable high-priority interrupts and low-priority interrupts
|
|
|
838 |
|
|
|
839 |
sprintf(output, "\r\nBegin Program\r\n");
|
|
|
840 |
DBG_PRINT_MAIN(output, strlen(output));
|
|
|
841 |
|
|
|
842 |
SSD1306_Begin(SSD1306_SWITCHCAPVCC);
|
|
|
843 |
memset(cardData, 0, 24);
|
|
|
844 |
memset(cardData_prev, 0, 24);
|
|
|
845 |
SSD1306_Clear_Display();
|
|
|
846 |
SSD1306_Set_Rotation(0);
|
|
|
847 |
SSD1306_Set_Cursor(0, 0);
|
|
|
848 |
|
|
|
849 |
version = NFC_Get_Firmware_Version();
|
|
|
850 |
while (!version.IC) {
|
|
|
851 |
sprintf(output, "Waiting for NFC board..\n");
|
|
|
852 |
SSD1306_Write_String(output, strlen(output));
|
|
|
853 |
SSD1306_Display();
|
|
|
854 |
Delay10KTCYx(255);
|
|
|
855 |
version = NFC_Get_Firmware_Version();
|
|
|
856 |
}
|
|
|
857 |
sprintf(output, "PN5%X Ver. %d.%d\n", version.IC, version.Ver, version.Rev);
|
|
|
858 |
SSD1306_Write_String(output, strlen(output));
|
|
|
859 |
SSD1306_Display();
|
|
|
860 |
NFC_SAMConfig();
|
|
|
861 |
|
|
|
862 |
while (1) {
|
|
|
863 |
|
|
|
864 |
// This query will not wait for a detection before responding
|
|
|
865 |
char length = NFC_Poll_Targets(1, 1, cardData);
|
|
|
866 |
if (!length) {
|
|
|
867 |
memset(cardData_prev, 0, 24);
|
|
|
868 |
} else if (length == 1) {
|
|
|
869 |
if (memcmp(&cardData[0].NFCID, &cardData_prev[0].NFCID, cardData[0].NFCID_LEN) == 0) {
|
|
|
870 |
// Do nothing
|
|
|
871 |
} else if (memcmp(&cardData[0].NFCID, &cardData_prev[1].NFCID, cardData[0].NFCID_LEN) == 0) {
|
|
|
872 |
memcpy((char *) &cardData_prev[0], (const char *) &cardData[0], 12);
|
|
|
873 |
} else {
|
|
|
874 |
sprintf(output, "UID: %02X %02X %02X %02X\n", cardData[0].NFCID[0], cardData[0].NFCID[1], cardData[0].NFCID[2], cardData[0].NFCID[3]);
|
|
|
875 |
SSD1306_Write_String(output, strlen(output));
|
|
|
876 |
SSD1306_Display();
|
|
|
877 |
memcpy((char *) &cardData_prev[0], (const char *) &cardData[0], 12);
|
|
|
878 |
}
|
|
|
879 |
memset(&cardData_prev[1], 0, 12);
|
|
|
880 |
} else if (length == 2) {
|
|
|
881 |
if (memcmp(&cardData[0].NFCID, &cardData_prev[0].NFCID, cardData[0].NFCID_LEN) == 0 &&
|
|
|
882 |
memcmp(&cardData[1].NFCID, &cardData_prev[1].NFCID, cardData[1].NFCID_LEN) == 0) {
|
|
|
883 |
// Do nothing
|
|
|
884 |
} else if (memcmp(&cardData[0].NFCID, &cardData_prev[1].NFCID, cardData[0].NFCID_LEN) == 0 &&
|
|
|
885 |
memcmp(&cardData[1].NFCID, &cardData_prev[0].NFCID, cardData[1].NFCID_LEN) == 0) {
|
|
|
886 |
memcpy((char *) &cardData_prev[0], (const char *) &cardData[0], 12);
|
|
|
887 |
memcpy((char *) &cardData_prev[1], (const char *) &cardData[1], 12);
|
|
|
888 |
} else if (memcmp(&cardData[0].NFCID, &cardData_prev[0].NFCID, cardData[0].NFCID_LEN) == 0) {
|
|
|
889 |
// First card matched
|
|
|
890 |
sprintf(output, "UID: %02X %02X %02X %02X\n", cardData[1].NFCID[0], cardData[1].NFCID[1], cardData[1].NFCID[2], cardData[1].NFCID[3]);
|
|
|
891 |
SSD1306_Write_String(output, strlen(output));
|
|
|
892 |
SSD1306_Display();
|
|
|
893 |
memcpy(&cardData_prev[1], (const char *) &cardData[1], 12);
|
|
|
894 |
} else if (memcmp(&cardData[1].NFCID, &cardData_prev[1].NFCID, cardData[1].NFCID_LEN) == 0) {
|
|
|
895 |
// Second card matched
|
|
|
896 |
sprintf(output, "UID: %02X %02X %02X %02X\n", cardData[0].NFCID[0], cardData[0].NFCID[1], cardData[0].NFCID[2], cardData[0].NFCID[3]);
|
|
|
897 |
SSD1306_Write_String(output, strlen(output));
|
|
|
898 |
SSD1306_Display();
|
|
|
899 |
memcpy((char *) &cardData_prev[0], (const char *) &cardData[0], 12);
|
|
|
900 |
} else {
|
|
|
901 |
// No match
|
|
|
902 |
sprintf(output, "UID: %02X %02X %02X %02X\n", cardData[0].NFCID[0], cardData[0].NFCID[1], cardData[0].NFCID[2], cardData[0].NFCID[3]);
|
|
|
903 |
SSD1306_Write_String(output, strlen(output));
|
|
|
904 |
SSD1306_Display();
|
|
|
905 |
memcpy((char *) &cardData_prev[0], (const char *) &cardData[0], 12);
|
|
|
906 |
sprintf(output, "UID: %02X %02X %02X %02X\n", cardData[1].NFCID[0], cardData[1].NFCID[1], cardData[1].NFCID[2], cardData[1].NFCID[3]);
|
|
|
907 |
SSD1306_Write_String(output, strlen(output));
|
|
|
908 |
SSD1306_Display();
|
|
|
909 |
memcpy((char *) &cardData_prev[1], (const char *) &cardData[1], 12);
|
|
|
910 |
}
|
|
|
911 |
}
|
|
|
912 |
}
|
|
|
913 |
}
|
|
|
914 |
#elif defined(_TEST_LUX_TO_CHAR_OLED)
|
|
|
915 |
void main(void) {
|
|
|
916 |
char output[64];
|
|
|
917 |
|
|
|
918 |
// Set all ports as digial I/O except for AN0-AN2 (pins 2-4)
|
|
|
919 |
ANCON0 = 0xF8;
|
|
|
920 |
ANCON1 = 0x1F;
|
|
|
921 |
|
|
|
922 |
I2C_DATA i2c_data;
|
|
|
923 |
I2C_Init(&i2c_data);
|
|
|
924 |
OLED_CHAR_DATA oled_data;
|
|
|
925 |
NHD_Init(&oled_data);
|
|
|
926 |
TSL2561_DATA lux_data;
|
|
|
927 |
LUX_Init(&lux_data, TSL2561_ADDR_FLOAT);
|
|
|
928 |
|
|
|
929 |
I2C_Configure_Master(I2C_400KHZ);
|
|
|
930 |
|
|
|
931 |
Interrupt_Init(); // Initialize the interrupt priorities
|
|
|
932 |
Interrupt_Enable(); // Enable high-priority interrupts and low-priority interrupts
|
|
|
933 |
|
|
|
934 |
NHD_Begin(16, 2);
|
|
|
935 |
|
|
|
936 |
// You can change the gain on the fly, to adapt to brighter/dimmer light situations
|
|
|
937 |
// LUX_SetGain(TSL2561_GAIN_0X); // set no gain (for bright situtations)
|
|
|
938 |
LUX_Set_Gain(TSL2561_GAIN_16X); // set 16x gain (for dim situations)
|
|
|
939 |
|
|
|
940 |
// Changing the integration time gives you a longer time over which to sense light
|
|
|
941 |
// longer timelines are slower, but are good in very low light situtations!
|
|
|
942 |
// LUX_SetTiming(TSL2561_INTEGRATIONTIME_13MS); // shortest integration time (bright light)
|
|
|
943 |
LUX_Set_Timing(TSL2561_INTEGRATIONTIME_101MS); // medium integration time (medium light)
|
|
|
944 |
// LUX_SetTiming(TSL2561_INTEGRATIONTIME_402MS); // longest integration time (dim light)
|
|
|
945 |
|
|
|
946 |
while (1) {
|
|
|
947 |
unsigned long lum = LUX_Get_Full_Luminosity();
|
|
|
948 |
unsigned int ir = lum >> 16;
|
|
|
949 |
unsigned int full = lum & 0xFFFF;
|
|
|
950 |
NHD_Set_Cursor(0, 0);
|
|
|
951 |
sprintf(output, "I: %d ", ir);
|
|
|
952 |
NHD_Write_String(output, strlen(output));
|
|
|
953 |
sprintf(output, "V: %d ", full - ir);
|
|
|
954 |
NHD_Write_String(output, strlen(output));
|
|
|
955 |
NHD_Set_Cursor(0, 1);
|
|
|
956 |
sprintf(output, "Lux: %ld ", LUX_Calculate_Lux(full, ir));
|
|
|
957 |
NHD_Write_String(output, strlen(output));
|
|
|
958 |
|
|
|
959 |
Delay10KTCYx(100);
|
|
|
960 |
}
|
|
|
961 |
}
|
|
|
962 |
#elif defined(_TEST_ADC)
|
|
|
963 |
void main(void) {
|
|
|
964 |
unsigned int x, y, z;
|
|
|
965 |
char buffer[60];
|
|
|
966 |
|
|
|
967 |
// Set all ports as digial I/O except for AN0-AN2 (pins 2-4)
|
|
|
968 |
ANCON0 = 0xF8;
|
|
|
969 |
ANCON1 = 0x1F;
|
|
|
970 |
|
|
|
971 |
UART_DATA uart_data;
|
|
|
972 |
UART1_Init(&uart_data); // Initialize the UART handler code
|
|
|
973 |
SPI_DATA spi_data;
|
|
|
974 |
SPI2_Init(&spi_data, SPI2_FOSC_8); // Initialize the SPI module
|
|
|
975 |
SSD1306_DATA ssd1306_data;
|
|
|
976 |
SSD1306_Init(&ssd1306_data); // Initialize the SSD1331 OLED display (uses SPI2)
|
|
|
977 |
ADC_DATA adc_data;
|
|
|
978 |
ADC_Init(&adc_data, ADC_TAD_20, ADC_FOSC_64_);
|
|
|
979 |
|
|
|
980 |
SSD1306_Begin(SSD1306_SWITCHCAPVCC);
|
|
|
981 |
|
|
|
982 |
Interrupt_Init(); // Initialize the interrupt priorities
|
|
|
983 |
Interrupt_Enable(); // Enable high-priority interrupts and low-priority interrupts
|
|
|
984 |
|
|
|
985 |
sprintf(buffer, "\r\nBegin Program\r\n");
|
|
|
986 |
SSD1306_Write_String(buffer, strlen(buffer));
|
|
|
987 |
|
|
|
988 |
memset(buffer, 0, 60);
|
|
|
989 |
SSD1306_Clear_Display();
|
|
|
990 |
SSD1306_Display();
|
|
|
991 |
|
|
|
992 |
while (1) {
|
|
|
993 |
// ADC read from AN0-AN2 and prints to display
|
|
|
994 |
ADC_Start(ADC_CHANNEL_AN2);
|
|
|
995 |
// SSD1306_Fill_Rect(0, 0, SSD1306_LCDWIDTH, 8, SSD1331_BLACK);
|
|
|
996 |
SSD1306_Set_Cursor(0, 0);
|
|
|
997 |
while (!ADC_Get_Result(&x));
|
|
|
998 |
sprintf(buffer, "X: %u", x);
|
|
|
999 |
SSD1306_Write_String(buffer, strlen(buffer));
|
|
|
1000 |
SSD1306_Display();
|
|
|
1001 |
|
|
|
1002 |
ADC_Start(ADC_CHANNEL_AN1);
|
|
|
1003 |
// SSD1306_Fill_Rect(0, 8, SSD1306_LCDWIDTH, 8, SSD1331_BLACK);
|
|
|
1004 |
SSD1306_Set_Cursor(0, 8);
|
|
|
1005 |
while (!ADC_Get_Result(&y));
|
|
|
1006 |
sprintf(buffer, "Y: %u", y);
|
|
|
1007 |
SSD1306_Write_String(buffer, strlen(buffer));
|
|
|
1008 |
SSD1306_Display();
|
|
|
1009 |
|
|
|
1010 |
ADC_Start(ADC_CHANNEL_AN0);
|
|
|
1011 |
// SSD1306_Fill_Rect(0, 16, SSD1306_LCDWIDTH, 8, SSD1331_BLACK);
|
|
|
1012 |
SSD1306_Set_Cursor(0, 16);
|
|
|
1013 |
while (!ADC_Get_Result(&z));
|
|
|
1014 |
sprintf(buffer, "Z: %u", z);
|
|
|
1015 |
SSD1306_Write_String(buffer, strlen(buffer));
|
|
|
1016 |
SSD1306_Display();
|
|
|
1017 |
}
|
|
|
1018 |
}
|
|
|
1019 |
#elif defined(_TEST_BMP)
|
|
|
1020 |
void main(void) {
|
|
|
1021 |
char output[64];
|
|
|
1022 |
|
|
|
1023 |
// Set all ports as digial I/O except for AN0-AN2 (pins 2-4)
|
|
|
1024 |
ANCON0 = 0xF8;
|
|
|
1025 |
ANCON1 = 0x1F;
|
|
|
1026 |
|
|
|
1027 |
UART_DATA uart_data;
|
|
|
1028 |
UART1_Init(&uart_data);
|
|
|
1029 |
I2C_DATA i2c_data;
|
|
|
1030 |
I2C_Init(&i2c_data);
|
|
|
1031 |
BMP085_DATA bmp_data;
|
|
|
1032 |
BMP_Init(&bmp_data);
|
|
|
1033 |
|
|
|
1034 |
I2C_Configure_Master(I2C_100KHZ);
|
|
|
1035 |
|
|
|
1036 |
Interrupt_Init(); // Initialize the interrupt priorities
|
|
|
1037 |
Interrupt_Enable(); // Enable high-priority interrupts and low-priority interrupts
|
|
|
1038 |
|
|
|
1039 |
BMP_Begin(BMP085_ULTRAHIGHRES);
|
|
|
1040 |
|
|
|
1041 |
while (1) {
|
|
|
1042 |
sprintf(output, "Temp: %f *C\r\n", BMP_Read_Temperature());
|
|
|
1043 |
DBG_PRINT_MAIN(output, strlen(output));
|
|
|
1044 |
sprintf(output, "Pressure: %ld Pa\r\n", BMP_Read_Pressure());
|
|
|
1045 |
DBG_PRINT_MAIN(output, strlen(output));
|
|
|
1046 |
sprintf(output, "Altitude: %f meters\r\n", BMP_Read_Altitude(101592));
|
|
|
1047 |
DBG_PRINT_MAIN(output, strlen(output));
|
|
|
1048 |
|
|
|
1049 |
Delay10KTCYx(255);
|
|
|
1050 |
Delay10KTCYx(255);
|
|
|
1051 |
Delay10KTCYx(255);
|
|
|
1052 |
Delay10KTCYx(255);
|
|
|
1053 |
}
|
|
|
1054 |
}
|
|
|
1055 |
#elif defined(_TEST_XBEE)
|
|
|
1056 |
void main(void) {
|
|
|
1057 |
unsigned int i, length = 0;
|
| 152 |
Kevin |
1058 |
unsigned char buffer[100];
|
|
|
1059 |
|
| 155 |
Kevin |
1060 |
XBEE_RX_AT_COMMAND_RESPONSE_FRAME *rx_at_cmd_response_frame;
|
|
|
1061 |
XBEE_RX_DATA_PACKET_FRAME *rx_data_frame;
|
|
|
1062 |
XBEE_RX_DATA_TX_STATUS_FRAME *rx_tx_status_frame;
|
|
|
1063 |
XBEE_RX_REMOTE_AT_COMMAND_FRAME *rx_remote_at_cmd_frame;
|
|
|
1064 |
XBEE_RX_NODE_IDENTIFICATION_INDICATOR_FRAME *rx_node_ident_frame;
|
|
|
1065 |
XBEE_RX_MODEM_STATUS_FRAME *rx_modem_status_frame;
|
|
|
1066 |
|
| 152 |
Kevin |
1067 |
/* --------------------- Oscillator Configuration --------------------- */
|
|
|
1068 |
// OSCTUNEbits.PLLEN = 1; // Enable 4x PLL
|
|
|
1069 |
OSCCONbits.IRCF = 0b111; // Set INTOSC postscaler to 8MHz
|
|
|
1070 |
OSCCONbits.SCS = 0b00; // Use 96MHz PLL as primary clock source
|
|
|
1071 |
/* -------------------------------------------------------------------- */
|
|
|
1072 |
|
|
|
1073 |
// Set all ports as digial I/O
|
|
|
1074 |
ANCON0 = 0xFF;
|
|
|
1075 |
ANCON1 = 0x1F;
|
|
|
1076 |
|
|
|
1077 |
UART1_Init(); // Initialize the UART handler code
|
| 155 |
Kevin |
1078 |
XBee_Init();
|
| 152 |
Kevin |
1079 |
|
| 155 |
Kevin |
1080 |
Interrupt_Enable(); // Enable high-priority interrupts and low-priority interrupts
|
|
|
1081 |
Interrupt_Init(); // Initialize the interrupt priorities
|
| 152 |
Kevin |
1082 |
|
| 155 |
Kevin |
1083 |
DBG_PRINT_MAIN("\r\nBegin Program\r\n");
|
| 152 |
Kevin |
1084 |
|
|
|
1085 |
while (1) {
|
|
|
1086 |
|
| 155 |
Kevin |
1087 |
//#define _ROUTER
|
|
|
1088 |
#define _COORDINATOR
|
|
|
1089 |
|
|
|
1090 |
#ifdef _ROUTER
|
|
|
1091 |
XBEE_TX_DATA_PACKET_FRAME *tx_data_frame;
|
|
|
1092 |
tx_data_frame = (void *) buffer;
|
|
|
1093 |
tx_data_frame->frame_type = XBEE_TX_DATA_PACKET;
|
|
|
1094 |
tx_data_frame->frame_id = 1;
|
|
|
1095 |
tx_data_frame->destination_64.UPPER_32.long_value = 0x00000000;
|
|
|
1096 |
tx_data_frame->destination_64.LOWER_32.long_value = 0x00000000;
|
|
|
1097 |
tx_data_frame->destination_16.INT_16.int_value = 0xFEFF;
|
|
|
1098 |
tx_data_frame->broadcast_radius = 0;
|
|
|
1099 |
tx_data_frame->options = 0;
|
|
|
1100 |
tx_data_frame->data[0] = 0x54;
|
|
|
1101 |
tx_data_frame->data[1] = 0x78;
|
|
|
1102 |
tx_data_frame->data[2] = 0x32;
|
|
|
1103 |
tx_data_frame->data[3] = 0x43;
|
|
|
1104 |
tx_data_frame->data[4] = 0x6F;
|
|
|
1105 |
tx_data_frame->data[5] = 0x6F;
|
|
|
1106 |
tx_data_frame->data[6] = 0x72;
|
|
|
1107 |
tx_data_frame->data[7] = 0x11;
|
|
|
1108 |
XBee_Process_Transmit_Frame(buffer, XBEE_TX_DATA_PACKET_FRAME_SIZE + 8);
|
|
|
1109 |
|
|
|
1110 |
Delay10KTCYx(255);
|
|
|
1111 |
Delay10KTCYx(255);
|
|
|
1112 |
Delay10KTCYx(255);
|
|
|
1113 |
Delay10KTCYx(255);
|
|
|
1114 |
Delay10KTCYx(255);
|
|
|
1115 |
Delay10KTCYx(255);
|
|
|
1116 |
Delay10KTCYx(255);
|
|
|
1117 |
Delay10KTCYx(255);
|
|
|
1118 |
#endif
|
|
|
1119 |
|
|
|
1120 |
#ifdef _COORDINATOR
|
|
|
1121 |
length = XBee_Get_Received_Frame(buffer);
|
|
|
1122 |
if (length != 0) {
|
|
|
1123 |
switch (*(unsigned char *) buffer) {
|
|
|
1124 |
case XBEE_RX_AT_COMMAND_RESPONSE:
|
|
|
1125 |
DBG_PRINT_MAIN("XBEE: parsing recieved AT command response frame\r\n");
|
|
|
1126 |
rx_at_cmd_response_frame = (void *) buffer;
|
|
|
1127 |
DBG_PRINT_MAIN("Frame ID: %u\r\n", rx_at_cmd_response_frame->frame_id);
|
|
|
1128 |
DBG_PRINT_MAIN("AT Command: %c%c Status: %02X\r\n", rx_at_cmd_response_frame->command[0], \\
|
|
|
1129 |
rx_at_cmd_response_frame->command[1], rx_at_cmd_response_frame->command_status);
|
|
|
1130 |
if (length > XBEE_RX_AT_COMMAND_RESPONSE_FRAME_SIZE) {
|
|
|
1131 |
DBG_PRINT_MAIN("Command Data: ");
|
|
|
1132 |
for (i = 0; i < length - XBEE_RX_AT_COMMAND_RESPONSE_FRAME_SIZE; i++) {
|
|
|
1133 |
DBG_PRINT_MAIN("%02X ", rx_at_cmd_response_frame->data[i]);
|
|
|
1134 |
}
|
|
|
1135 |
DBG_PRINT_MAIN("\r\n");
|
|
|
1136 |
}
|
|
|
1137 |
break;
|
|
|
1138 |
case XBEE_RX_DATA_PACKET:
|
|
|
1139 |
DBG_PRINT_MAIN("XBEE: parsing recieved data recieved frame\r\n");
|
|
|
1140 |
rx_data_frame = (void *) buffer;
|
|
|
1141 |
XBee_Convert_Endian_64(&(rx_data_frame->source_64));
|
|
|
1142 |
XBee_Convert_Endian_16(&(rx_data_frame->source_16));
|
|
|
1143 |
DBG_PRINT_MAIN("Source 64: %08lX %08lX Source 16: %04X Options: %02X\r\n", \\
|
|
|
1144 |
rx_data_frame->source_64.UPPER_32.long_value, \\
|
|
|
1145 |
rx_data_frame->source_64.LOWER_32.long_value, \\
|
|
|
1146 |
rx_data_frame->source_16.INT_16.int_value, \\
|
|
|
1147 |
rx_data_frame->recieve_options);
|
|
|
1148 |
DBG_PRINT_MAIN("Data: ");
|
|
|
1149 |
for (i = 0; i < length - XBEE_RX_DATA_PACKET_FRAME_SIZE; i++) {
|
|
|
1150 |
DBG_PRINT_MAIN("%02X ", rx_data_frame->data[i]);
|
|
|
1151 |
}
|
|
|
1152 |
DBG_PRINT_MAIN("\r\n");
|
|
|
1153 |
break;
|
|
|
1154 |
case XBEE_RX_DATA_TX_STATUS:
|
|
|
1155 |
DBG_PRINT_MAIN("XBEE: parsing recieved TX status frame\r\n");
|
|
|
1156 |
rx_tx_status_frame = (void *) buffer;
|
|
|
1157 |
XBee_Convert_Endian_16(&(rx_tx_status_frame->destination_16));
|
|
|
1158 |
DBG_PRINT_MAIN("Frame ID: %u Destination 16: %04X\r\n", \\
|
|
|
1159 |
rx_tx_status_frame->frame_id, rx_tx_status_frame->destination_16.INT_16.int_value);
|
|
|
1160 |
DBG_PRINT_MAIN("Transmit Retry Count: %02X Delivery Status: %02X Discovery Status: %02X\r\n", \\
|
|
|
1161 |
rx_tx_status_frame->transmit_retry_count, rx_tx_status_frame->delivery_status, \\
|
|
|
1162 |
rx_tx_status_frame->discovery_status);
|
|
|
1163 |
break;
|
|
|
1164 |
case XBEE_RX_IO_DATA_SAMPLE:
|
|
|
1165 |
DBG_PRINT_MAIN("XBEE: parsing recieved IO data sample frame\r\n");
|
|
|
1166 |
break;
|
|
|
1167 |
case XBEE_RX_EXPLICIT_COMMAND:
|
|
|
1168 |
DBG_PRINT_MAIN("XBEE: parsing recieved explicit command frame\r\n");
|
|
|
1169 |
break;
|
|
|
1170 |
case XBEE_RX_REMOTE_AT_COMMAND_RESPONSE:
|
|
|
1171 |
DBG_PRINT_MAIN("XBEE: parsing recieved remote AT command frame\r\n");
|
|
|
1172 |
rx_remote_at_cmd_frame = (void *) buffer;
|
|
|
1173 |
break;
|
|
|
1174 |
case XBEE_RX_ROUTE_RECORD:
|
|
|
1175 |
DBG_PRINT_MAIN("XBEE: parsing recieved route record frame\r\n");
|
|
|
1176 |
break;
|
|
|
1177 |
case XBEE_RX_NODE_IDENTIFICATION:
|
|
|
1178 |
DBG_PRINT_MAIN("XBEE: parsing recieved node identification frame\r\n");
|
|
|
1179 |
rx_node_ident_frame = (void *) buffer;
|
|
|
1180 |
XBee_Convert_Endian_64(&(rx_node_ident_frame->source_64));
|
|
|
1181 |
XBee_Convert_Endian_16(&(rx_node_ident_frame->source_16));
|
|
|
1182 |
XBee_Convert_Endian_64(&(rx_node_ident_frame->remote_64));
|
|
|
1183 |
XBee_Convert_Endian_16(&(rx_node_ident_frame->remote_16));
|
|
|
1184 |
XBee_Convert_Endian_16(&(rx_node_ident_frame->parent_16));
|
|
|
1185 |
DBG_PRINT_MAIN("Source 64: %08lX %08lX Source 16: %04X Options: %02X\r\n", \\
|
|
|
1186 |
rx_node_ident_frame->source_64.UPPER_32.long_value, \\
|
|
|
1187 |
rx_node_ident_frame->source_64.LOWER_32.long_value, \\
|
|
|
1188 |
rx_node_ident_frame->source_16.INT_16.int_value, \\
|
|
|
1189 |
rx_node_ident_frame->recieve_options);
|
|
|
1190 |
DBG_PRINT_MAIN("Remote 64: %08lX %08lX Remote 16: %04X Parent 16: %04X\r\n", \\
|
|
|
1191 |
rx_node_ident_frame->remote_64.UPPER_32.long_value, \\
|
|
|
1192 |
rx_node_ident_frame->remote_64.LOWER_32.long_value, \\
|
|
|
1193 |
rx_node_ident_frame->remote_16.INT_16.int_value, \\
|
|
|
1194 |
rx_node_ident_frame->parent_16.INT_16.int_value);
|
|
|
1195 |
DBG_PRINT_MAIN("Device Type: %02X Source Event: %02X\r\n", \\
|
|
|
1196 |
rx_node_ident_frame->device_type, rx_node_ident_frame->source_event);
|
|
|
1197 |
break;
|
|
|
1198 |
case XBEE_RX_FRAME_MODEM_STATUS:
|
|
|
1199 |
DBG_PRINT_MAIN("XBEE: parsing recieved modem status frame\r\n");
|
|
|
1200 |
rx_modem_status_frame = (void *) buffer;
|
|
|
1201 |
DBG_PRINT_MAIN("Status: %02X\r\n", rx_modem_status_frame->status);
|
|
|
1202 |
break;
|
|
|
1203 |
default:
|
|
|
1204 |
DBG_PRINT_MAIN("??\r\n");
|
|
|
1205 |
break;
|
|
|
1206 |
}
|
|
|
1207 |
}
|
|
|
1208 |
#endif
|
|
|
1209 |
|
| 152 |
Kevin |
1210 |
}
|
|
|
1211 |
}
|
|
|
1212 |
#else
|
|
|
1213 |
int main() {
|
| 155 |
Kevin |
1214 |
|
| 152 |
Kevin |
1215 |
}
|
|
|
1216 |
#endif
|